Toro 07154SL Service Manualpdresser 1800 2500 Preface Publication

Removal (Fig. 5)
Position Topdresser on a level  surface with hopper
empty. Chock  Topdresser wheels to  prevent machine
from moving.
Topdresser 2500
1.
5
6
3
2.
Remove conveyor  belt from  machine (see Opera-
tor’s Manual):
4
A.  Remove conveyor  chain guard and  disconnect
drive chain (Figs. 6 and 7).
8
3
2
7
B.  Remove fasteners that secure hopper to frame.
Pivot hopper rearward and lean against wall or post
(Fig. 8). Do not allow hopper to rest  against rear of
machine as  damage may  result to  brush or  other
components.
1
Figure 6
1.
2.
3.
4.
Carriage screw
Chain guard
Flat washer
Lock nut
5.
6.
7.
8.
Cap screw
IMPORTANT: Make  sure  hopper is  pivoted be-
yond center and secured to wall  or post to pre-
vent it from accidentally falling on work area (Fig.
8).
Lock washer
Hyd conveyor motor
Drive chain
Topdresser 1800
C. Loosen jam nuts that tension conveyor belt.
8
D. On  right side of machine,  loosen fasteners that
secure slider bed to frame. On left side of machine,
remove fasteners that secure slider bed to frame.
7
2
9
E.  Remove conveyor belt from machine.
6
NOTE:  Normal roller  rotation is  clockwise as  viewed
5
from left side of machine (Fig. 9).
4
3
10
3.
Loosen  set screw  (item 22)  that  secures bearing
2
locking collar to roller shaft. Using a punch and hammer,
rotate locking collar in the opposite direction of normal
roller rotation to loosen collar.
1
Figure 7
4.
Support roller to prevent it from shifting.
1.
2.
3.
4.
5.
Lock nut
Flat washer
Spacer
6.
7.
8.
9.
Cap screw
Lock washer
Cap screw
5.
cure bearings to  frame. Remove roller assembly  from
machine.
Remove four (4) screws  and lock washers that se-
Guard
Hyd conveyor motor
Chain guard
10. Drive chain
6.
that secure sprocket to roller. Remove sprocket, square
key and sprocket spacer from roller.
If rear roller was removed, remove two (2) set screws
7.
Slide bearings from roller shaft.
8.
for wear or damage. Replace worn or torn components
to insure proper operation of machine.
Inspect conveyor belt, hopper seals and gate  edge
Installation (Fig. 5)
1.
Clean roller shaft ends and apply antiseize lubricant
to shaft ends. Slide bearing assembly onto each end of
roller shaft. Make sure that locking collar is orientated to-
ward the end of the roller. Do not tighten set screws  in
locking collars.
Figure 8
Topdresser 1800 & 2500
Page 5 – 9
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 100 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website