Toro Commercial Products Lubrication Oils Grease 99040SL Thistentionally Blank Lubricants

Adjustments
AUGER DRIVE ADJUSTMENT
WARNING
C
B
Do not over-tighten, as this may lift the lever and
cause auger drive to be engaged without
depressing the Auger Control.
A
1.
2.
Check that the auger cable (A, Figure 15) is on top of
cable button (B) as show in Figure 15.
With the drive lever released, the hook (B, Figure
16b)
should barely touch the lever (C) without raising
it. There can be a maximum 1/32ā€ clearance as
shown.
Figure 15.  Auger Cable Button
A.  Auger Drive Cable
B.  Auger Cable Button
C.  Lever
3.
To adjust, loosen nut (D) by holding the adjusting
flats (A) and turning nut (D).  Turn adjustment flats
and hold screw.  The adjustment screw is a phillips
screw and the head can be held or turned by insert-
ing a screwdriver through the spring (F).
4.
5.
Hold adjusting flats (A) and tighten nut (D).
A
D
Start unit and check auger.  Auger must not be
engaged unless auger control is depressed.
6.
7.
8.
9.
With engine running, fully depress auger control, the
auger should engage and run normally.
E
Release auger control. Auger must stop within 5
seconds.
If auger does not operate properly, stop engine and
recheck drive linkage adjustments.
F
If auger linkage is properly adjusted, auger drive belt
tension may require adjustment. See adjusting the
auger belt in this section of the manual
1/32ā€
(.080cm)
TRACTION DRIVE CABLE
ADJUSTMENT
C
B
Initial Adjustment
Figure 16.  Auger Drive Adjustment
A.  Adjusting Flats
B.  Spring Hook
C.  Lever
WARNING
D.  Nut
E.  Adjustment Screw
F.  Spring
Do not over-tighten, as this may cause traction
drive to engage without depressing the traction
drive control (arm must remain in down position).
Verify that the cables are not over-tightened: With
speed selector in position 1 and traction drive
control fully released, push snowthrower forward.
The unit should move forward freely.
1.
2.
With the drive lever released there should be no
slack in the cable when moved slightly from side to
side.
To adjust tension on the cable slide the cable boot
(A, Figure 17) off the cable adjustment bracket (D).
If unit does not move forward freely, the cable has
been over-tightened. To remedy, loosen tension
on clutch cable slightly, and recheck.
3.  Remove the ā€œZā€ hook (C) from the cable adjustment
bracket (D) to a different adjustment hole. The cable
should have no slack.  The cable should have no ten-
sion or load.
24
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website