Toro Commercial Products Lubrication Oils Grease 99040SL Thistentionally Blank Lubricants

Adjustments
A
A
B
B
B
C
D
C
4-5/16”
(10.95cm)
Figure 17.  Traction Drive Cable Adjustment
A.  Cable Boot
B.  Traction Drive Cable
C.  “Z” Hook
Figure 18. Friction Disc Measurement
A.  Friction Disc
B.  Frame
D.  Cable Adjustment Bracket
A
Note: If the cable is too slack the unit will not drive.  If the
cable is too tight the drive will be engaged without push-
ing the handles down.
E
B
4.
Slide the cable boot (A) over the cable adjustment
bracket.
C
Run-In Adjustment
D
ALL MODELS
Figure 19. Speed Selector Linkage
A.  Speed Selector Rod
B.  Jam Nut
C.  Ball Joint
D.  Locknut
1.
After 5 hours of use, check for proper adjustment.
Readjust clutch cable if necessary by increasing ten-
sion on cable. A small amount of arm movement is
permissible if unit passes operating checks described
in the Warning above.
E.  Shift Rod
5.
Note the position of the friction disc (A, Figure 18).
The correct distance from the right side of the friction
wheel to the outside of the frame is 4-5/16” (10.95
cm).  If the friction disc is not in the correct position,
adjust as follows.
WARNING
Gasoline is highly flammable and must be
handled with care. Drain gasoline outdoors. Never
drain the tank when the engine is still hot from
recent operation. Do not allow open flame,
smoking or matches in the area. Avoid over-filling
and wipe up any spills.
6.
Position the shift speed lever in the lowest forward
speed.
7.
8.
9.
Loosen the jam nut (B, Figure 19).
Remove locknut (D).
1.
Remove the gas from the gas tank.
Disconnect the spark plug wire.
Move the friction disc (A, Figure 18) to the correct
distance, 4-5/16” (10.95 cm).
2.
3.
Stand snowthrower on the front of the auger housing
(C, Figure 25)
10.
Turn the ball joint (C, Figure 15) until it is aligned with
the mounting hole in the shifter rod (E). When
aligned, attach the ball joint(C) to the shifter rod (E)
and tighten the jam nut (B).
2.
Loosen the capscrews (A, Figure 25) on each side of
the bottom panel (B).
3.
4.
Remove the bottom panel (B).
11.
12.
Check that the snowthrower operates in R1.  If not
follow procedures 1-11 and readjust as necessary.
Position the shift speed lever in the lowest forward
speed.
Install the bottom panel (B, Figure 25) and tighten the
capscrews (A).
25
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website