Note: Do not use synthetic oil.
Important: Do not get oil on the rubber wheel or
the aluminum friction drive plate because the traction
drive will slip (Figure 44).
6.
Install the pipe plug in the gearbox.
ChangingtheEngineOil
1. Drain the gasoline from the fuel tank.
2.
Tip the snowthrower forward onto its auger housing
and block it so that it cannot fall.
Change the engine oil after the first 2 operating hours, then
yearly thereafter. If possible, run the engine just before
changing the oil because warm oil flows better and carries
more contaminants.
3.
Remove the back cover (Figure 45).
Max. fill: 26 oz. (0.77 l), type: automotive detergent oil with
an API service classification of SF, SG, SH, SJ, SL, or higher.
•
•
For temperatures above 32°F (0°C), use SAE 30W.
For temperatures between 0°F and 32°F (-18°C to 0°C),
use SAE 5W30 or SAE 10W.
Figure45
•
For air temperatures below 0°F (-18°C), use SAE 0W30.
Clean the area around the oil drain cap (Figure 43).
1.
Backcover
1.
4.
5.
Move the speed selector lever to Position R2.
Dip your finger in automotive engine oil and lightly
lubricate hex shaft.
6.
7.
8.
Move the speed selector lever to Position 6.
Lubricate the other end of the hex shaft.
Move the speed selector lever forward and rearward
a few times.
Figure43
1.
Oildraincap
9.
Install the back cover and return the snowthrower to
the operating position.
2.
3.
Slide an oil drain pan under the drain extension and
remove the oil drain cap.
Drain the oil.
InspectingandReplacingthe
SparkPlug
Note: Dispose of the used oil properly at a local
recycling center.
Use a Champion RJ-19LM or equivalent spark plug. Check
and gap the spark yearly, and replace the plug if necessary.
4.
5.
Install the oil drain cap.
Fill the crankcase with oil. Refer to Filling the Engine
Crankcase with Oil.
1.
2.
3.
Clean around the base of the spark plug.
Remove the spark plug.
LubricatingtheHexShaft
Examine the spark plug and replace it if it is cracked,
fouled, dirty, or if the electrodes are worn.
Lightly lubricate the hex shaft yearly with automotive engine
oil (Figure 44).
Important: Do not clean the electrodes because
grit could enter the cylinder and damage the
engine.
4.
Set the gap between the electrodes on the spark plug at
0.030
inch (0.76 mm) (Figure 46).
Figure46
1.
0.030inch(0.76mm)
Figure44
5.
Install the spark plug by hand and then torque it to 15
ft-lb (20.4 N·m).
1.
2.
Hexshaft
Aluminumfrictionplate
3.
Rubberwheel
18
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38635, Toro Power Max 828LE |
| Model Number | 38635 |
| Model Year | 2007 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 270000001 - 270999999 |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Swath | 28 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | LH318SA-156564H |
| Engine Motor Size | 318cc |
| Engine Motor Type | 4 Cycle, 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro Power Max 828LE 38635 Snow Blower Operators Manual, 2007 4.0 out of 4.0 based on 1 product reviews. Love the snow blower just need the Manuel