HANDLES & CONTROL CABLES
2.
With the engine off and the spark plug wire discon-
5. Install the screen panel with the two flanged head
self-tapping screws. Make sure that the top edge
of the screen panel is under the lip at the top of
the housing. The screen is installed, sharp edge
down, to allow air to be drawn in through the screen
panel on top of the deck and down underneath the
deck. This venting improves the airflow underneath
the deck thereby improving quality of cut and
bagging performance. Be sure to clean the screen
on occasion, especially if quality of cut or bagging
performance has degraded.
nected, cock and lift the control bar to engage the
blade. Tape the control bar to the handle with the
blade engaged, then measure the length of the over-
travel spring (Fig. 296). When adjusted properly, it
should measure 1” (25mm). If it does, skip ahead
to step 5. Otherwise proceed with adjustment in the
following step.
Note: An overly tight cable will cause the BBC to
disengage before the bail can be raised to
the normal operating position. Cock the bail
downward and raise to the handle. If the BBC
disengages and you hear the brake engage
with a snap, the cable is likely too tight.
Excessive cable tension causes the control
hook in the control box to release. It doesn’t
do any permanent damage to any parts.
Loosen the cable slightly and repeat the test.
1”
On BBC models, the control bail also controls the
transmission belt engagement. The adjustment point
is a knob about halfway between the control panel and
transmission. Ideally, the cable should be set so that
the transmission drive will disengage when the bail is
lowered about 1” (25mm). This allows the bail to be
lowered so that the wheels stop driving and the BBC
remains engaged, but the gap isn’t so large that the
handle is hard to hold (Fig. 297). This measurement is
not an exact requirement. It can be varied to accommo-
date a customer with small hands, etc.
Fig 296
fig. 68
A. Plastic fitting
B. Cable fitting
C. Spring
3.
4.
There is a turnbuckle in the cable about halfway
between the control panel and the chassis. Adjust
the turnbuckle until the over-travel spring measures
1”
(25mm).
Remove the tape from the handle and disengage the
blade.
1” (25mm)
Fig 297
fig 20
WPM Drive Systems Manual
9-15
Categories | Lawn Mower Manual, Parts and Accessories Manuals, Toro Lawn Mower Manual |
---|---|
Tags | Toro 16400, Toro 16401, Toro 16575, Toro 16576, Toro 16585, Toro 16775, Toro 16776, Toro 16785, Toro 20003, Toro 20005, Toro 20007, Toro 20008, Toro 20009, Toro 20013, Toro 20014, Toro 20019, Toro 20022, Toro 20023, Toro 20025, Toro 20027, Toro 20029, Toro 20030, Toro 20033, Toro 20038, Toro 20041, Toro 20042, Toro 20044, Toro 20045, Toro 20046, Toro 20048, Toro 20049, Toro 20051, Toro 20061, Toro SR 21OS |
Model Number | 16576 |
Model Year | 1990, 1996, 1999, 2001, 2003, 2004, 2005, 2006, 2007 |
Download File |
|
Document Type | Operator's Manual |
Language | English |
Serial Number | 0000001 - 0999999 |
Product Name | Toro Lawnmower |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Product Type | Walk Behind Mower |
Swath | 21 inch |
Discharge | Side |
Engine Manufacturer | Tecumseh |
Engine Oil Type | 21 oz. (.62l) 30w or 10w-30 / API SH or higher |
Engine Motor Model # | TVS100-44021B |
Engine Motor Type | 4 Cycle |
Transmission Type | Hand Push |
Spark Plug | Champion RJ17LM |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)