THREE SPEED TRANSMISSION
3.
Removal of the input shaft and pulley assembly can
5. Remove the cotter pin from the top of the shift fork
and remove the shift lever.
be difficult because the input pinion has a tendency
to turn as the pulley nut is loosened. This situation
can be addressed by using an impact wrench or by
removing the 20 (B) and 25 (A) tooth gears (Fig.
6. Carefully pull the output shaft from the transmission
case, clean, and inspect all components for wear
or damage. Check the input shaft ball bearing for
roughness or excessive drag and replace any parts
necessary. If ball bearing replacement is required,
press the ball bearing out using an arbor press.
122)
from the intermediate shaft and then putting
the intermediate shaft assembly back onto the
transmission. The hexagonal intermediate shaft
can then be held with a 7/16” end wrench while the
pulley nut is loosened.
7.
If service of any of the output shaft gears, or the
gear selection system, is required, remove the left
pivot arm as described under “Rear Height-of-Cut
and Wheel Pinion Clutch – Disassembly” on page
Note: A cut-away transmission cover can be
fabricated to hold the intermediate shaft in
place to facilitate pulley nut removal.
5-4
and 5-5.
A
Note: It is possible to replace the shift keys and
spring clip without removing the pivot arm
if the roll pin securing the gear sleeve to the
output shaft is first driven out. However, it
is not recommended since inspection of the
inside of the output gears is not possible.
B
8.
Pull the output shaft bushing, the spacer, the shift
collar, the shift keys and spring clip, and the shift key
sleeve from the output shaft.
9.
Remove the three output shaft gears form the output
shaft.
10.
Drive out the roll pin securing the gear sleeve to the
output shaft. Remove the gear sleeve and remaining
output shaft bushing. Inspect all parts for wear and
damage and replace if necessary.
Fig 122
3428-0058
A. 25-tooth gear
B. 20-tooth gear
4.
Remove the intermediate shaft from the transmission
and clean. Inspect all gears for wear, cracks, and/
or broken teeth. Inspect the bushings for excessive
wear. Replace any parts necessary. Be careful not to
lose the two spacers that fit between the bevel gear
and the bushing.
WPM Drive Systems Manual
5-7
| Categories | Lawn Mower Manual, Parts and Accessories Manuals, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 16400, Toro 16401, Toro 16575, Toro 16576, Toro 16585, Toro 16775, Toro 16776, Toro 16785, Toro 20003, Toro 20005, Toro 20007, Toro 20008, Toro 20009, Toro 20013, Toro 20014, Toro 20019, Toro 20022, Toro 20023, Toro 20025, Toro 20027, Toro 20029, Toro 20030, Toro 20033, Toro 20038, Toro 20041, Toro 20042, Toro 20044, Toro 20045, Toro 20046, Toro 20048, Toro 20049, Toro 20051, Toro 20061, Toro SR 21OS |
| Model Number | 16576 |
| Model Year | 1990, 1996, 1999, 2001, 2003, 2004, 2005, 2006, 2007 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 0000001 - 0999999 |
| Product Name | Toro Lawnmower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Swath | 21 inch |
| Discharge | Side |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 30w or 10w-30 / API SH or higher |
| Engine Motor Model # | TVS100-44021B |
| Engine Motor Type | 4 Cycle |
| Transmission Type | Hand Push |
| Spark Plug | Champion RJ17LM |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)