Toro CCR 3650 GTS 38517 Snow Blower Operators Manual, 2002

Adjusting the Control Cable
Important
you disengage the control bar for the rotor blades to stop
properly.
The control cable must contain slack when
Check the control cable for proper adjustment initially,
after the first operating hour, and then annually thereafter.
Adjusting the Cable
Checking the Cable
For Models 38515 and 38516 only:
1.
2.
Stop the engine and wait for all moving parts to stop.
1.
2.
Unhook the spring end from the control bar (Fig. 16).
Move the control bar back toward the handle to remove
the slack in the cable as shown in Figure 16 (for models
Slide the spring cover off the spring and the cable
adjuster (Fig. 18).
38515
and 38516) or Figure 17 (for models 38517 and
38518).
4
1
2
Models 38515
and 38516
897
1
2
3
4
Figure 18
4
3
1.
2.
Cable
3.
4.
Cable adjuster
Spring
Z-fitting
1
3.
Unhook the Z-fitting from the cable adjuster (Fig. 18)
and position the Z-fitting in a higher or lower hole on
the adjuster to obtain a proper gap of 1/16 to 1/8 in. (2
to 3 mm) between the control bar and the handle
(Fig. 16).
5
6
m-5533/m-2708
2
Figure 16
Note: Moving the Z-fitting to a hole closer to the spring
decreases the gap between the control bar and the
handle; moving it to a hole farther from the spring
increases the gap.
1.
Top hole
4.
5.
6.
Control bar
2.
3.
Bottom hole
Spring cover
1/16 to 1/8 in. (2 to 3 mm)
gap
Control cable
4.
Slide the spring cover over the cable adjuster and the
spring.
Models 38517
and 38518
5.   Hook the spring into the bottom hole of the control bar.
2
3
6.
Check the adjustment (refer to steps 2 and 3 of
Checking the Cable on page 16).
4
1
5
m-5519
Figure 17
1.
Cable
4.
5.
Bottom hole
2.
3.
Control bar
Top hole
1/16 to 1/8 in. (2 to 3 mm)
gap
3.
Ensure that a 1/16 to 1/8 in. (2 to 3 mm) gap exists
between the control bar and the handle. Refer to the
inset in Figure 5 (models 38515 and 38516) or the inset
in Figure 9 (models 38517 and 38518). To adjust the
cable, go to Adjusting the Cable on page 16.
16
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags,
Model Number38517
Model Year2002
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOperator's Manual
LanguageEnglish, Français
Serial Number220000001 - 220999999
Product NameToro CCR 3650 GTS Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesCCR 1000/2400/2500, Single Stage, Snowthrower
Swath20 inch
DischargeSingle Stage
Engine ManufacturerToro
Engine Oil TypeToro 2 cycle / NMMA-TCW3
Engine Motor Model #R-tek
Engine Motor Size5 hp
Engine Motor Type2 Cycle EPA1
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website