For Models 38517 and 38518:
drive system. To remove moisture, start the rotor and
operate it without a load for 30 seconds. Once you remove
the moisture, the drive belt should not slip.
1.
Unhook the upper cable end from the hole in the control
bar (Fig. 17).
2.
Slide the spring cover up the cable to expose the cable
adjuster (Fig. 19).
Replacing the Rotor Blades
Before each season, inspect the rotor blades for wear. When
a rotor blade edge has worn down to the wear indicator
hole (Fig. 20), replace both rotor blades to ensure proper
performance and to prevent damage to the underside of the
snowthrower.
3
2
1
1
m-5538a
Figure 20
1.
Wear indicator hole
Figure 19
1.
2.
Cable adjuster
Z-fitting
3. Spring cover
Important
Replace the scraper whenever you replace
the rotor blades. This ensures proper snowthrower
operation and performance.
3.
Unhook the Z-fitting from the cable adjuster (Fig. 18)
and position it in a higher or lower hole on the adjuster
to obtain a gap of 1/16 to 1/8 in. (2 to 3 mm) between
the control bar and the handle (Fig. 9).
Note: The running time and the roughness of the driveway
or the sidewalk determines the wear rate of the rotor blades.
Note: You need a No. T27 torx driver to complete this
Note: Moving the Z-fitting to a hole closer to the spring
decreases the gap between the control bar and the
handle; moving it to a hole farther from the spring
increases the gap.
procedure.
1.
2.
3.
Stop the engine and wait for all moving parts to stop.
Remove the key from the switch.
4.
5.
Slide the spring cover over the cable adjuster.
Remove the control panel and disconnect the wire from
the spark plug. Refer to steps 3 through 5 of Replacing
the Spark Plug on page 19.
Install the upper cable end into the bottom hole in the
control bar.
6.
Check the adjustment (refer to steps 2 and 3 of
Checking the Cable on page 16).
After extended use, the drive belt may wear and lose its
proper belt tension. Improper belt tension causes the belt to
slip and decreases the performance under a heavy load. Belt
slippage may occur after 2 or 3 seasons of normal usage (10
to 15 hours). If the drive belt slips (continuously squeals)
under a heavy load, increase the belt tension by inserting
the spring end into the top hole of the control bar (Fig. 16
or Fig. 17).
Note: Using the incorrect adjusting hole can reduce the
drive belt life. Occasional belt slippage (squealing) may
occur in extremely wet conditions due to moisture in the
17
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 3650, Toro 38517 |
| Model Number | 38517 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 220000001 - 220999999 |
| Product Name | Toro CCR 3650 GTS Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 1000/2400/2500, Single Stage, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Toro |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | R-tek |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)