Husqvarna 323P4 325P5 X-Series Chainsaw Owners Manual

MAINTENANCE
Carburettor
CAUTION!  If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions. After the engine has used 8-10 tanks of fuel the
engine will be run-in.To ensure that it continues to run at peak
performance and to minimise harmful exhaust emissions
after the running-in period, ask your dealer/service workshop
(who will have a rev counter at their disposal) to adjust your
carburettor.
Rec. idle speed 2700 rpm
Recommended max. speed: See the Technical data
section.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
!
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
!
Fine adjustment
Function
When the machine has been ”run-in” the carburettor
should be finely adjusted. The fine adjustment should
be carried out by a qualified person. First adjust the L-
jet, then the idling screw T and then the H-jet.
The carburettor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the carburettor.
The air/fuel mixture is adjustable. Correct adjustment is
essential to get the best performance from the machine.
Conditions
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted. If you adjust
the carburettor when the air filter is dirty it will result in a
leaner mixture when the filter is finally cleaned. This can
lead to serious engine damage.
The setting of the carburetor means that the engine is
adepted to local conditions, for example, the climate,
altitude, fuel and the type of 2-stroke oil.
Carefully turn both jets, L and H, so that they are midway
between fully screwed in and fully screwed out.
The carburettor has three adjustment controls:
L = Low speed jet
Do not attempt to adjust the L and H jets beyond either
stop as this could cause damage.
H = High speed jet
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
T = Idle adjustment screw
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
Low speed jet L
Try to find the highest idling speed, turning the low speed
needle L clockwise respectively counter-clockwise.When the
highest speed has been found, turn the low speed needle L 1/
4
turn counter-clockwise.
The L and H-jets are used to adjust the supply of fuel to
match the rate that air is admitted, which is controlled with
the throttle. If they are screwed clockwise the air/fuel ratio
becomes leaner (less fuel) and if they are turned anti-
clockwise the ratio becomes richer (more fuel). A lean
mixture gives a higher engine speed and a rich mixture
gives a lower engine speed.
+
1/4
L
The T-screw regulates the throttle setting at idle speed. If
the T-screw is turned clockwise this gives a higher idle
speed; turning it anti-clockwise gives a lower idle speed.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
Basic setting
The basic carburettor settings are adjusted during testing
at the factory. The basic setting is richer than the optimal
setting and should be maintained for the first few hours the
machine is in use. The carburettor should then be finely
adjusted. Fine adjustment should be carried out by a
skilled technician.
20
English
Product Specification
CategoriesChainsaw Manuals, Husqvarna Chainsaw Manuals
Tags, ,
Model Year2003
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOperator's Manual
LanguageEnglish
Product BrandHusqvarna, Chainsaw
Document File TypePDF
Publisherhusqvarna.com
Wikipedia's PageHusqvarna
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website