5.
Loosen the idler pulley mounting nut on the differential
idler pulley and pivot the idler pulley counterclockwise
away from the backside of the belt to release the belt
tension.
2
6.
Remove the 2 capscrews and locknuts securing the front
clutch housing to the side plate (Fig. 42).
7.
Rotate the housing 180° so the bottom of the housing
points upward.
1
8.
Remove the 2 capscrews and locknuts securing the right
rear bearing housing to the side plate (Fig. 42).
9.
Rotate the housing 180° so the bottom of the housing
points upward. Remove old belt.
10.
Slide the new belt over the rotated housing covers, the
differential cover sections, and onto the differential
pulleys.
Figure 43
1.
Traction cable
2.
Front jam nut
11.
12.
Ensure that the idler pulley is positioned against the
backside of belt.
Rotate both housings back into the upright position and
secure them to the sideplate with the capscrews and nuts
previously removed.
Adjusting the Service/Park
Brake
13.
14.
Adjust the differential belt tension; refer to Adjusting
the Differential Belt, page 27.
If the service/park brake slips when operated, an adjustment
is required.
Adjust the belt tension on the traction drive and reel
drive belts; refer to Adjusting the Traction Drive Belt,
page 26, and Adjusting the Reel Drive Belt, page
NO TAG.
1.
2.
Move the service/park brake lever to the Off position.
Loosen the retainer securing the V-belt cover and pivot
the cover open (Fig. 44).
15.
Install the differential, traction drive, and reel drive
covers.
Adjusting the Traction Control
If the traction control does not engage or it slips during
operation, an adjustment is required.
1
1.
2.
Move the traction control to the Disengaged position.
2
Loosen the retainer securing the V-belt cover and pivot
the cover open (Fig. 40).
3.
To increase the cable tension, loosen the front cable jam
nut and tighten the back cable jam nut (Fig. 43) until a
force of 3 to 5 lb. is required to engage the traction
control. Measure the force at the control knob.
Figure 44
1.
Service/park brake cable
2. Front jam nut
4.
5.
6.
Tighten the front cable jam nut.
Close the cover and secure the retainer.
Check the control operation.
3.
To increase the cable tension, loosen the front cable jam
nut and tighten the back cable jam nut (Fig. 44) until a
force of 3 to 5 lb. is required to engage brake. Measure
the force at the lever knob. Do not over adjust it so that
the brake band drags.
4.
Close the cover and secure the retainer.
29
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 04048, Toro 04052, Toro 04060, Toro Greensmaster 1000, Toro Greensmaster 1600, Toro Greensmaster 800 |
| Model Year | 2003 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)