Toro Power Max 828LXE 38630 Snow Blower Operators Manual, 2007

Unclogging the Discharge
Chute
If the chute does not move, refer to Adjusting the
Discharge Chute Latch.
If the chute does not turn as far to the left as it does
to the right, ensure that the cable is routed to the
inside of the handles. Refer to Installing the Upper
Handle.
If the auger/impeller is running but there is no snow
coming out of the discharge chute, the discharge chute
may be clogged.
To unclog the discharge chute, stay in the operating
position and release the left hand (traction) lever.
While running the auger/impeller, push down on
the handles to raise the front of the snowthrower
a few inches (centimeters) off the pavement. Then
lift the handles quickly to bump the front of the
snowthrower on the pavement. Repeat if necessary
until a stream of snow comes out the discharge chute.
If the chute does not lock into place when you release
the trigger cap, refer to Adjusting the Discharge
Chute Latch.
Moving the Chute Deflector
Hold the blue trigger cap down and move the Quick
Stick forward to lower the chute deflector; move it
rearward to raise the chute deflector (Figure 40).
If you cannot unclog the discharge chute by bumping
the front of the snowthrower, stop the engine,
wait for all moving parts to stop, and use a stick;
never use your hand.
Important: Unclogging the discharge chute by
bumping the front of the snowthrower on the
pavement may cause the skids to move. Adjust
the skids and tighten the skid bolts securely.
Preventing Freeze-up
In snowy and cold conditions, some controls and
moving parts may freeze. Do not use excessive
force when trying to operate frozen controls. If
you have difficulty operating any control or part,
start the engine and let it run for a few minutes.
Figure 40
After using the snowthrower, let the engine run for a
few minutes to prevent moving parts from freezing.
Engage the auger/impeller to clear any remaining
snow from inside the housing. Rotate the Quick
Stick to prevent it from freezing. Stop the engine,
wait for all moving parts to stop, and remove all ice
and snow from the snowthrower.
With the engine off, pull the recoil starter handle
several times to prevent the recoil starter from
freezing up.
17
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags,
Model Number38630
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOperator's Manual
LanguageEnglish
Serial Number270000001 - 270999999
Product NameToro Power Max 828 LXE Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesTwo Stage Power Max
Swath28 inch
DischargeTwo Stage
Engine ManufacturerTecumseh
Engine Oil Type26 oz. (.8l) 5w-30 or 10w / API SH or higher
Gearbox Lubricant4.5 oz. (133ml) SAE 90 GL5 or higher
Engine Motor Model #LH318SA-156563H
Engine Motor Type4 Cycle CARB2, EPA2
Transmission Speed6 Forward/2 Reverse
Transmission TypeFriction Disc
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website