10.
11.
12.
Remove the ignition key.
Disconnect the spark plug wire.
Remove the spark plug, add 1 oz. (30 ml) of oil
through the spark plug hole, and pull the starter rope
slowly several times to distribute oil throughout the
cylinder to prevent cylinder corrosion during the
off-season.
13.
14.
Loosely install the spark plug.
Dispose of any unused fuel properly. Recycle it
according to local codes, or use it in your automobile.
Note: Do not store stabilized fuel for more than
Figure 62
90
days.
15.
Clean the snowthrower thoroughly.
Storage
16. Touch up chipped surfaces with paint available
from an Authorized Service Dealer. Sand affected
areas before painting, and use a rust preventative to
prevent the metal parts from rusting.
17.
Tighten all loose screws, bolts, and locknuts. Repair
or replace any damaged parts.
•
•
•
Gasoline vapors can explode.
Do not store gasoline more than 30 days.
18.
Cover the snowthrower and store it in a clean, dry
place out of the reach of children. Allow the engine
to cool before storing it in any enclosure.
Do not store the snowthrower in an
enclosure near an open flame.
•
Allow the engine to cool before storing it.
Removing the Snowthrower
from Storage
Preparing the Snowthrower
for Storage
1.
Remove the spark plug and spin the engine rapidly
using the starter to blow the excess oil from the
cylinder.
1.
2.
3.
On the last refueling of the year, add fuel stabilizer
to fresh fuel as directed by the engine manufacturer.
2.
Install the spark plug by hand and then torque it to
15 ft-lb (20.4 N·m).
Run the engine for 10 minutes to distribute the
conditioned fuel through the fuel system.
3.
4.
Connect the spark plug wire.
Loosen the hose clamp that secures the fuel line to
the valve and slide the fuel line off the fuel shutoff
valve.
Perform the annual maintenance procedures as given
in the Recommended Maintenance Schedule.
4.
Open the fuel shutoff valve and allow the fuel to
drain out of the fuel tank into an approved fuel
container.
5.
6.
Install the fuel line onto the fuel shutoff valve and
secure it with a hose clamp.
Run the snowthrower until the engine stops from
running out of fuel.
7.
8.
Prime the engine and start it again.
Allow the engine to run until it stops. When you can
no longer start the engine, it is sufficiently dry.
9.
Stop the engine and allow it to cool.
25
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38630, Toro Power Max 828LXE |
| Model Number | 38630 |
| Model Year | 2007 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 270000001 - 270999999 |
| Product Name | Toro Power Max 828 LXE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Two Stage Power Max |
| Swath | 28 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | LH318SA-156563H |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)