Toro Power Max 828LXE 38630 Snow Blower Operators Manual, 2007

surfaces, adjust the skids further down to prevent
the snowthrower from picking up rocks.
5.
6.
Move the skids down until they are even with the
ground.
Firmly tighten the nuts that secure both skids to the
auger sides.
Note: To quickly adjust the skids if they loosen,
support the scraper 1/8 inch (3 mm)  off the
pavement, then adjust the skids down to  the
pavement.
Note: If the skids become excessively worn, you
can turn them over and set the unused side toward
the pavement.
Figure 42
Checking and Adjusting the
Traction Cable
Checking and Adjusting the
Skids and Scraper
Service Interval: Yearly
Service Interval:  After the first 2 hours—Inspect
the traction cable and adjust it if
necessary.
Check the skids and the scraper to ensure that the auger
does not contact the paved or gravel surface. Adjust the
skids and the scraper as needed to compensate for wear.
Yearly—Inspect the traction cable
and adjust or replace it if necessary.
If the snowthrower does not drive in the forward or
reverse speeds or it drives when you release the traction
lever, adjust the traction cable.
1.
Check the tire pressure. Refer to Checking the Tire
Pressure.
2.
Loosen the nuts that secure both skids to the
auger sides until the skids slide up and down easily
(Figure 43).
With the traction lever disengaged, check the pin in the
elongated slot in the left side of the snowthrower above
the tire. There should be a gap of 1/32 to 1/16 inch (1
to 1.5 mm) from the front of the slot to the front edge
of the pin (Figure 44).
Figure 43
3.
4.
Support the side plates so that they are at least 1/2
inch (1.3 cm) above a level surface.
Figure 44
1.
Pin
Important:  The auger blades must be
supported above the ground by the skids.
If the left hand (traction) cable is not properly adjusted,
do the following steps:
Ensure that the scraper is 1/8 inch (3 mm) above
and parallel to a level surface.
1.
Loosen the jam nut.
Note: If the pavement is cracked, rough, or uneven,
adjust the skids to raise the scraper.  For gravel
20
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags,
Model Number38630
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOperator's Manual
LanguageEnglish
Serial Number270000001 - 270999999
Product NameToro Power Max 828 LXE Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesTwo Stage Power Max
Swath28 inch
DischargeTwo Stage
Engine ManufacturerTecumseh
Engine Oil Type26 oz. (.8l) 5w-30 or 10w / API SH or higher
Gearbox Lubricant4.5 oz. (133ml) SAE 90 GL5 or higher
Engine Motor Model #LH318SA-156563H
Engine Motor Type4 Cycle CARB2, EPA2
Transmission Speed6 Forward/2 Reverse
Transmission TypeFriction Disc
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website