dryers. Allow the engine to cool before storing in
any enclosure.
• Perform only those maintenance instructions
described in this manual. Before performing any
maintenance, service, or adjustment, stop the engine,
remove the key, and disconnect the wire from the
spark plug. If major repairs are ever needed, contact
your Authorized Service Dealer.
•
Always refer to the Operator’s Manual for important
details if the snow thrower is to be stored for an
extended period.
•
•
Maintain or replace safety and instruction labels, as
necessary.
• Do not change the governor settings on the engine.
Run the machine a few minutes after throwing snow
to prevent freeze-up of the rotor blades.
•
When storing the snowthrower for more than
30 days, drain the fuel from the fuel tank to prevent
a potential hazard. Store fuel in an approved fuel
container. Remove the key from the ignition switch
before storing the snowthrower.
Toro Snowthrower Safety
The following list contains safety information specific
to Toro products or other safety information that you
must know.
•
Purchase only genuine Toro replacement parts and
accessories.
•
Rotating auger/impeller can cut off or injure
fingers or hands. Stay behind the handles and away
from the discharge opening while operating the
snowthrower. Keep your face, hands, feet, and
any other part of your body or clothing away
from moving or rotating parts.
Safety and Instructional
Decals
Important: Safety and instruction decals are
located near areas of potential danger. Replace
damaged decals.
•
Before adjusting, cleaning, inspecting,
troubleshooting, or repairing the snowthrower, stop
the engine, remove the key, and wait for all
moving parts to stop. Disconnect the wire from
the spark plug and keep it away from the spark
plug to prevent someone from accidentally
starting the engine.
•
•
Before leaving the operating position, stop the
engine, remove the key, and wait for all moving parts
to stop.
To unclog the discharge chute, stay in the operating
position and release the left hand (traction) lever.
While running the auger/impeller, push down on
the handles to raise the front of the snowthrower
a few inches (centimeters) off the pavement. Then
lift the handles quickly to bump the front of the
snowthrower on the pavement. Repeat if necessary
until a stream of snow comes out the discharge chute.
53-7670
1.
Cutting/dismemberment of foot, auger
•
•
If you cannot unclog the discharge chute by bumping
the front of the snowthrower, stop the engine, wait
for all moving parts to stop, and use the cleanout
tool; never use your hand.
If a shield, safety device, or decal is damaged,
illegible, or lost, repair or replace it before beginning
operation.
•
•
•
Do not smoke while handling gasoline.
Do not use the snowthrower on a roof.
Do not touch the engine while it is running or soon
after it has stopped because the engine may be hot
enough to cause a burn.
4
Categories | Snow Blower Manuals, Toro Snow Blower |
---|---|
Tags | Toro 38630, Toro Power Max 828LXE |
Model Number | 38630 |
Model Year | 2007 |
Download File |
|
Document Type | Operator's Manual |
Language | English |
Serial Number | 270000001 - 270999999 |
Product Name | Toro Power Max 828 LXE Snowthrower |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
Product Type | Snowthrower |
Product Series | Two Stage Power Max |
Swath | 28 inch |
Discharge | Two Stage |
Engine Manufacturer | Tecumseh |
Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
Engine Motor Model # | LH318SA-156563H |
Engine Motor Type | 4 Cycle CARB2, EPA2 |
Transmission Speed | 6 Forward/2 Reverse |
Transmission Type | Friction Disc |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)