Operating the Quick Stick®
Moving the Chute Deflector
Hold the blue trigger cap down and move the Quick
Stick forward to lower the chute deflector; move it
rearward to raise the chute deflector (Figure 31).
Hold the blue trigger cap down to use the Quick Stick
to move the discharge chute and the chute deflector.
Release the trigger cap to lock the discharge chute and
chute deflector into position (Figure 29).
Figure 31
Figure 29
Moving the Discharge Chute
Unclogging the Discharge
Chute
Hold the blue trigger cap down and move the Quick
Stick to the left to move the discharge chute to the left;
move the Quick Stick to the right to move the discharge
chute to the right (Figure 30).
If the auger/impeller is running but there is no snow
coming out of the discharge chute, the discharge chute
may be clogged.
•
To unclog the discharge chute, stay in the operating
position and release the left hand (traction) lever.
While running the auger/impeller, push down on
the handles to raise the front of the snowthrower
a few inches (centimeters) off the pavement. Then
lift the handles quickly to bump the front of the
snowthrower on the pavement. Repeat if necessary
until a stream of snow comes out the discharge chute.
•
If you cannot unclog the discharge chute by bumping
the front of the snowthrower, stop the engine, wait
for all moving parts to stop, and use the snow
cleanout tool; never use your hand.
Important: Unclogging the discharge chute by
bumping the front of the snowthrower on the
pavement may cause the skids to move. Adjust
the skids and tighten the skid bolts securely.
Figure 30
•
•
If the chute does not move, refer to Adjusting the
Discharge Chute Latch.
Preventing Freeze-up
If the chute does not turn as far to the left as it does
to the right, ensure that the cable is routed to the
inside of the handles. Refer to Installing the Upper
Handle.
• In snowy and cold conditions, some controls and
moving parts may freeze. Do not use excessive
force when trying to operate frozen controls. If
you have difficulty operating any control or part,
start the engine and let it run for a few minutes.
•
If the chute does not lock into place when you release
the trigger cap, refer to Adjusting the Discharge
Chute Latch.
• After using the snowthrower, let the engine run for a
few minutes to prevent moving parts from freezing.
15
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38610, Toro Power Max 6000 |
| Model Number | 38610 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Product Name | Toro Power Max 6000 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 084333-0197-E1 |
| Engine Motor Size | 141cc |
| Engine Motor Type | 2 Cycle EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)