Storage
•
•
•
Gasoline vapors can explode.
Do not store gasoline more than 30 days.
Do not store the snowthrower in an
enclosure near an open flame.
•
Allow the engine to cool before storing it.
Figure 49
1.
Cable conduit
2.
Cable clamp
Preparing the Snowthrower
for Storage
3.
Grasp the cable conduit and move it toward the front
of the machine until the discharge chute latch fully
engages the gear teeth (Figure 49 and Figure 50).
1.
On the last refueling of the year, add fuel stabilizer
to fresh fuel as directed by the engine manufacturer.
Note: If you use Toro 50:1 2-Cycle Oil (Fuel
Stabilizer Added), you do not need to add a fuel
stabilizer/conditioner.
2.
3.
Run the engine for 5 minutes to distribute the
conditioned fuel through the fuel system.
Run the snowthrower until the engine stops from
running out of fuel.
4.
5.
Prime the engine and start it again.
Figure 50
Allow the engine to run until it stops. When you can
no longer start the engine, it is sufficiently dry.
1.
Discharge chute latch
2. Gear teeth
6.
7.
8.
9.
Stop the engine and allow it to cool.
Remove the ignition key.
Note: The latch is spring loaded and will naturally
move into the teeth of the gear (Figure 50).
Disconnect the spark plug wire.
4.
Remove any slack in the cable by pulling the cable
conduit rearward.
Dispose of any unused fuel properly. Recycle it
according to local codes, or use it in your automobile.
5.
6.
Tighten the bolt on the cable clamp.
Install and secure the gear cover.
Note: Do not store stabilized fuel for more than
90
days.
10.
11.
Clean the snowthrower thoroughly.
Replacing the Drive Belts
Tighten all loose screws, bolts, and locknuts. Repair
or replace any damaged parts.
If the auger/impeller drive belt or the traction drive belt
becomes worn, oil-soaked, or otherwise damaged, go
to www.Toro.com for additional service information or
have an Authorized Service Dealer replace the belt.
Removing the Snowthrower
from Storage
1.
2.
Connect the spark plug wire.
Perform the annual maintenance procedures as given
in the Recommended Maintenance Schedule.
22
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38610, Toro Power Max 6000 |
| Model Number | 38610 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Product Name | Toro Power Max 6000 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 084333-0197-E1 |
| Engine Motor Size | 141cc |
| Engine Motor Type | 2 Cycle EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)