Maintenance
Note: Determine the left and right sides of the machine from the normal operating position.
Recommended Maintenance Schedule(s)
Maintenance Service
Maintenance Procedure
Interval
•
•
Inspect the traction cable and adjust it if necessary.
Check the auger/impeller cable and adjust it if necessary.
After the first 2 hours
•
•
•
•
•
•
Check the skids and the scraper and adjust them if necessary.
Inspect the traction cable and adjust or replace it if necessary.
Check the auger/impeller cable and adjust it if necessary.
Check the auger gearbox oil and add oil if necessary.
Lubricate the hex shaft.
Yearly
Inspect the spark plug. Replace and/or gap it if necessary.
•
•
Check the air pressure in the tires and inflate them to 17–20 psi (116–137 kPa).
Drain the gasoline and run the engine to dry out the fuel tank and the carburetor at
the end of the season.
Yearly or before storage
•
Have an Authorized Service Dealer inspect and replace the traction drive belt and/or
the auger/impeller drive belt, if necessary.
Important: You can find more information about maintaining and servicing your snowthrower at
www.Toro.com.
Preparing for Maintenance
1.
2.
3.
4.
Move the snowthrower to a level surface.
Stop the engine and wait for all moving parts to stop.
Remove the ignition key.
After performing the maintenance procedure(s),
insert the ignition key.
Figure 32
Checking and Adjusting the
Skids and Scraper
3.
4.
Support the side plates so that they are at least 1/2
inch (1.3 cm) above a level surface.
Service Interval: Yearly—Check the skids and the
scraper and adjust them if necessary.
Important: The auger blades must be
supported above the ground by the skids.
Check the skids and the scraper to ensure that the auger
does not contact the paved or gravel surface. Adjust the
skids and the scraper as needed to compensate for wear.
Ensure that the scraper is 1/8 inch (3 mm) above
and parallel to a level surface.
Note: If the pavement is cracked, rough, or uneven,
adjust the skids to raise the scraper. For gravel
surfaces, adjust the skids further down to prevent
the snowthrower from picking up rocks.
1.
Check the tire pressure. Refer to Checking the Tire
Pressure.
2.
Loosen the nuts that secure both skids to the
auger sides until the skids slide up and down easily
(Figure 32).
5.
6.
Move the skids down until they are even with the
ground.
Firmly tighten the nuts that secure both skids to the
auger sides.
Note: To quickly adjust the skids if they loosen,
support the scraper 1/8 inch (3 mm) off the
17
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38610, Toro Power Max 6000 |
| Model Number | 38610 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Product Name | Toro Power Max 6000 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 084333-0197-E1 |
| Engine Motor Size | 141cc |
| Engine Motor Type | 2 Cycle EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)