4.
Adjust Runners
7. Grasp starter handle and pull rope out
slowly until it pulls harder. Let rope rewind
slowly.
Check and adjust Runners (see Service and
Adjustments). Allow 1/8 in. (3 mm) between
scraper blade and hard, smooth surface(s).
Allow 1-1/4 in. (30 mm) between scraper
blade and uneven or gravel surfaces.
8. Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
IMPORTANT: DO NOT let Starter Handle
snap against Starter.
5.
Check Engine Fuel & Crankcase Oil
9.
Repeat steps 7 and 8 until engine starts.
(If engine does not start, refer to
Troubleshooting.)
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
10.
11.
Adjust choke as needed.
Set throttle to Part Throttle or Slow
position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
Check and add fuel if required. Check that the
engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
Electric Start (932037, 038, 039)
TO STOP IN AN EMERGENCY
1. Connect extension cord to prongs on
starter.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
Immediately release both control bails to stop
unit in an emergency. Stop engine, remove
key and wait for all rotating parts to stop before
leaving operator’s position.
2.
Plug extension into 120V 3-wire,
grounded outlet.
STARTING AND SHUT OFF
3.
4.
Turn discharge chute straight ahead.
Make sure that the traction clutch and
attachment drive clutch bails are fully
disengaged.
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire Owner/
Operator Manual and the Engine
Manual first.
5.
Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
6.
Insert key into ignition switch on engine
and push into "Run" position. DO NOT
twist key after it is inserted.
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent freeze-up.
NOTE: Try out each control without the engine
running to see how it works and what it does.
7. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
Manual Start
8.
9.
Set throttle to proper starting position.
1.
2.
Turn discharge chute straight ahead.
Press starter button on engine until
engine starts.
Make sure that the traction clutch and
attachment drive clutch bails are fully
disengaged.
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting.)
3.
Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
10. Adjust choke as needed.
(-26° C) additional priming may be needed.
11.
Disconnect power cord from outlet, then
starter.
4.
If engine is cold, apply choke. See Engine
Manual for detailed instructions.
12.
Set throttle to Part Throttle or Slow
position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
NOTE: A warm engine requires less choking
than a cold engine.
5.
6.
Set throttle to proper starting position.
Insert key into ignition switch and push
into RUN position. DO NOT twist key after
it is inserted.
GB - 16
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 932037-724, Ariens 932038-5520, Ariens 932039-624, Ariens 932505-724, Ariens 932507-520, Ariens 932508-624 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)