Craftsman 247.88955 24-Inch Snow Blower Owners Manual

SERVICE AND MAINTENANCE
CheckingsparkPlug
Warning
Spark Plug
DO NOT check for spark with spark plug removed. DO NOT crank
engine with spark plug removed.
Warning
Ifnotthetoenginetouch thehasmuffler.been running, the muffler will be very  hot. Be careful
NOTE:  Check the spark plug once a season  or every 25 hours of
operation. Change the spark plug once a season or every 100 hours.
To ensure proper engine operation, the spark plug must be properly
gapped and free of deposits.
1
.
Remove the spark plug boot and use a spark plug wrench to
remove the plug. See Figure 14.
2
.
Visually inspect the spark plug. Discard the  spark plug if there is
apparent wear, or if the insulator is cracked or chipped. Clean the
spark plug with a wire brush if it is to be reused.
Spark Plug Boot
Figure 14
3
.
Measure the plug gap with a feeler gauge. Correct as necessary
by bending side electrode. See Figure 15. The gap should  be set
to .02-.03 inches (0.60-0.80 mm).
4.
Check that the spark plug washer is in good condition  and thread
the spark plug in by hand to prevent cross-threading.
After the spark plug is seated, tighten with a spark plug wrench to
compress the washer.
Electrode
5.
NOTE: When installing a new spark plug, tighten 1⁄2-turn  after the
spark plug seats to compress the washer. When reinstalling a used
spark plug, tighten 1⁄8-  to 1⁄4-turn after the spark plug seats to
compress the washer.
.02-.03
(0.60-0.80
in.
mm)
CaUtio n
The spark plug must be tightened securely. A loose spark plug can
become very hot and can damage the engine.
Figure 15
LUbriCatio n
gearshaft
The gear (hex) shaft should be lubricated at least  once a season or
after every 25 hours of operation.
1
.
To prevent spillage, remove all fuel from tank by running engine
until it stops.
2
3
.
.
Carefully pivot the snow thrower up and forward so that it rests on
the auger housing.
Remove the lower frame cover from the underside of the snow
thrower by removing the four self-tapping screws which secure it.
Apply a light coating of engine oil (or 3-in-1 oil) to the  hex shaft.
See Figure 16.
4.
NOTE: When lubricating the hex shaft, be careful not to get any oil  on
the aluminum drive plate or rubber friction wheel. Doing so will  hinder
the snow thrower’s drive system. Wipe off any excess or spilled oil.
Figure 16
17
Product Specification
CategoriesCraftsman Snow Blower Manuals, Snow Blower Manuals
Tags
Model Number247.88955
Model Year2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 68 pages
Document TypeOperator's Manual
LanguageEnglish, Español
Product NameCraftsman 24-Inch Snow Thrower
Product BrandCraftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Swath24 inch
Engine ManufacturerCraftsman
Engine Oil TypeSAE 5W30, 4-Cycle Engine Oil (Quart)
Recommended for Temperature:
- Above 32°F: SAE 30W Straight Grade;
- 0°F to 32°F: SAE 5W-30 or SAE 10W-30 Multi Grade;
- Below O°F: SAE 0W-30 Synthetic
Engine Motor Model #ZS365-SUA
Document File TypePDF
Publishercraftsman.com
Wikipedia's PageCraftsman (tools)
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website