MAINTENANCE AND REPAIR INSTRUCTIONS
SPARK ARRESTOR MAINTENANCE
Adjusting Nut
1.
2.
Remove the muffler cover. See Rocker Arm Clearance.
With a flat blade screwdriver or Torx T-20 bit, remove the
screw attaching the spark arrestor cover to the muffler
(Fig. 41).
Rocker Arm
Muffler
Spark Arrestor Screen
.003–.006
in.
mm)
(.076–.152
Feeler Gauge
Tab
Screw
Spark Arrestor Cover
Slot
Valve Stem
Fig. 41
3.
Pull the tab on the spark arrestor cover out of the muffler.
Remove the spark arrestor cover.
Fig. 39
•
To decrease clearance, turn the adjusting nut
clockwise.
4.
5.
6.
Remove the spark arrestor screen from the spark arrestor cover.
Clean screen with a wire brush or replace it.
Reinstall the spark arrestor screen, spark arrestor cover
and screw.
b. Recheck both clearances, and adjust as necessary.
11.
Reinstall the rocker arm cover using a new gasket. Torque
the screw to 20–30 in•lb (2.2–3.4 N•m).
CLEANING
12.
13.
Reinstall the engine cover. Check alignment of the cover
before tightening the screws. Tighten screws.
WARNING: To avoid serious personal injury,
always turn your unit off and allow it to cool before
you clean or service it.
Reinstall the muffler cover. Slip the rear tab on the muffler
cover into the engine cover rear slot. Then slide the
remaining slots into the tabs until they snap into place
(Fig. 34).
Use a small brush to clean off the outside of the unit. Do not
use strong detergents. Household cleaners that contain
aromatic oils such as pine and lemon, and solvents such as
kerosene, can damage plastic housing or handle. Wipe off any
moisture with a soft cloth.
14.
15.
Check the spark plug and reinstall. See Replacing the
Spark Plug (below).
STORAGE
•
Replace the spark plug wire.
Never store the unit with fuel in the tank where fumes may
reach an open flame or spark.
Allow the engine to cool before storing.
Lock up the unit to prevent unauthorized use or damage.
Store the unit in a dry, well-ventilated area.
• Store the unit out of the reach of children.
REPLACING THE SPARK PLUG
Use a replacement part number 791-180852B spark plug. The
correct air gap is 0.025 in. (0.655 mm.). Remove the plug after
every 25 hours of operation and check its condition.
•
•
•
1.
Stop the engine and allow it to cool. Grasp the plug wire
firmly and pull the cap from the spark plug.
LONG TERM STORAGE
2.
Clean dirt from around the spark plug. Remove the spark
plug from the cylinder head by turning a 5/8 in. socket
counterclockwise.
1.
Drain all gasoline from the gas tank into a container. Do
not use gas that has been stored for more than 60 days.
Dispose of the old gasoline in accordance to Federal,
State, and Local regulations.
Start the engine and allow it to run until it stalls. This ensures
that all gasoline has been drained from the carburetor.
Allow the engine to cool. Remove the spark plug and put 1
oz. (30 ml) of high quality motor oil into the cylinder. Pull
the starter rope slowly to distribute the oil. Reinstall the
spark plug.
3.
4.
Replace cracked, fouled or
dirty spark plug. Set the air
gap at 0.025 in. (0.655 mm.)
2.
3.
using a feeler gauge (Fig. 40).
0.025 in.
(0.655 mm.)
Install a correctly-gapped
spark plug in the cylinder
head. Turn the 5/8 in.
NOTE:
Remove the spark plug and drain all of the oil from the
socket clockwise until snug.
cylinder before attempting to start the trimmer after storage.
Change the oil, referring to Changing the Oil (p. 9). Dispose
of the old oil in accordance to Federal, State and Local
regulations.
Thoroughly clean the unit and inspect for any loose or
damaged parts. Repair or replace damaged parts and tighten
loose screws, nuts or bolts. The unit is ready for storage.
If using a torque wrench torque
to:
110-120
4.
5.
Fig. 40
in.•lb. (12.3-13.5 N•m)
Do not over tighten.
WARNING: Do not sand blast, scrape or clean
electrodes. Grit in the engine could damage the
cylinder.
TRANSPORTING
•
•
•
•
Allow the engine to cool before transporting.
Secure the unit while transporting.
Drain the gas tank before transporting.
Tighten gas cap before transporting.
12
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD TB26TB, Troy-Bilt TB26TB |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated MTD Troy-Bilt TB26TB 4 Cycle Trimmer Lawn Mower Owners Manual 3.0 out of 3.0 based on 1 product reviews.