English
Warning!
Warning!
Never operate your chain saw without a
front hand guard. In a kickback situation
this guard helps protect your left hand
and other parts of your body. In addition,
removal of the hand guard on a saw
equipped with a Quickstop chain brake
will deactivate the chain brake.
Never run the chain saw above idle
speed for more than 3 seconds when
the chain brake is engaged or when the
chain is pinched or otherwise caught in
the cut. Clutch slippage can cause
excessive heat, leading to severe dam-
age of the motor housing, clutch and
oiler component and may interfere with
the operation of the chain brake. If
clutch slippage in excess of 3 seconds
has occurred, allow the motor housing
to cool before proceeding and check the
operation of your chain brake as
Warning!
No Quickstop or other chain brake
device prevents kickback. These
devices are designed to reduce the risk
of kickback injury, if activated, in certain
kickback situations. In order for the
Quickstop to reduce the risk of kickback
injury, it must be properly maintained
and in good working order. See the
chapter of your instruction manual enti-
tled "Chain Brake" and the section
"Maintenance, Repair and Storing" at
the end of these Safety Precautions. In
addition, there must be enough distance
between the bar and the operator to
ensure that the Quickstop has sufficient
time to activate and stop the chain
before potential contact with the
operator.
described in the chapter entitled "Chain
Brake" of your instruction manual. Also
make sure that the chain is not turning
at idle speed (see above at "Important
Adjustments").
When a kickback occurs, the guide bar
may rotate around the front handle. If the
cutting position is such that the
Low kickback saw chain and reduced
kickback bars
operator's left hand is gripping the front
handle behind the hand guard, and if the
left hand rotates around the front handle
and makes a sufficiently forceful contact
with the front hand guard, which is the
Quickstop activating lever, this contact
will activate a properly maintained
Quickstop chain brake. The chain brake
on newer STIHL chain saws can also be
activated by inertia. If the kickback
forces are sufficiently high, the hand
guard is accelerated towards the bar
nose even without hand contact. See the
chapter entitled "Chain Brake" of your
instruction manual.
STIHL offers a variety of bars and
chains. STIHL reduced kickback bars
and low kickback chains are designed to
reduce the risk of kickback injury. Other
chains are designed to obtain higher
cutting efficiency or sharpening ease but
may result in higher kickback tendency.
STIHL has developed a color code
system to help you identify the STIHL
reduced kickback bars and low kickback
chains. Cutting attachments with green
warning decals or green labels on the
packaging are designed to reduce the
risk of kickback injury. The matching of
green decaled powerheads under
Warning!
An improperly maintained chain brake
may increase the time needed to stop
the chain after activation, or may not
activate at all.
3.8
cubic inches (62 cm³) displacement
with green labeled bars and green
labeled chains gives compliance with
the computed kickback angle
requirements of ANSI B 175.1-2000
MS 171, MS 181, MS 181 C, MS 211, MS 211 C
13
| Categories | Chainsaw Manuals, STIHL Chainsaw Manuals |
|---|---|
| Tags | STIHL MS 171, STIHL MS 181, STIHL MS 211 |
| Download File |
|
| Language | English, Español |
| Product Brand | STIHL. Stihl Inc, USA - Corporate phone: (757) 486-9100. International Support Information: http://stihl.com Email: info@stihl.com, Chainsaw |
| Document File Type | |
| Publisher | stihl.com |
| Wikipedia's Page | Stihl |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)