English
Fold the grip flush with
the top of the cap. If the
grip does not lie com-
pletely flush with the cap
and the detent on the grip
does not fit in the corre-
sponding recess in the
filler opening, the cap is
not properly seated and
tightened and you must
repeat the above steps.
Warning!
Warning!
Always check your power tool for proper
condition and operation before starting,
particularly the throttle trigger, throttle
trigger interlock, stop switch and cutting
tool. The throttle trigger must move
freely and always spring back to the idle
position. Never attempt to modify the
controls or safety devices.
Proper tension of the chain is extremely
important. In order to avoid improper
setting, the tensioning procedure must
be followed as described in your man-
ual. Always make sure the hexagonal
nut(s) for the sprocket cover is (are)
tightened securely after tensioning the
chain in order to secure the bar. Never
start the saw with the sprocket cover
loose. Check chain tension once more
after having tightened the nut(s) and
thereafter at regular intervals (whenever
the saw is shut off). If the chain
Screw cap
Warning!
Never operate your power tool if it is
damaged, improperly adjusted or main-
tained, or not completely or securely
assembled.
Warning!
Unit vibrations can cause an improperly
tightened fuel filler cap to loosen or
come off and spill quantities of fuel. In
order to reduce the risk of fuel spillage
and fire, tighten the fuel filler cap by
hand as securely as possible.
becomes loose while cutting, shut off
the engine and then tighten. Never try to
adjust the chain while the engine is
running!
Warning!
Keep the handles clean and dry at all
times; it is particularly important to keep
them free of moisture, pitch, oil, fuel mix,
grease or resin in order for you to
maintain a firm grip and properly control
your power tool.
Check that the spark plug boot is
securely mounted on the spark plug – a
loose boot may cause arcing that could
ignite combustible fumes and cause a
fire.
The screwdriver end of
the STIHL combination
wrench or other similar
tool can be used as an
aid in tightening slotted
fuel filler caps.
For proper assembly of the bar and
chain follow the procedure described in
the chapter "Mounting the Bar and
Chain" of your instruction manual.
STIHL Oilomatic chain, guide bar and
sprocket must match each other in
gauge and pitch. Before replacing any
bar and chain, see the chapter entitled
"Specifications" in the instruction
Starting
See "Fueling" chapter in your instruction
manual.
Warning!
To reduce the risk of fire and burn inju-
ries, start the engine at least 10 feet
(3 meters) from the fueling spot, out-
doors only.
Before Starting
Take off the chain guard (scabbard) and
inspect the saw for proper condition and
operation. (See the maintenance chart
near the end of the instruction manual.)
manual and the section "Kickback" and
the "ANSI B 175.1-2000 chain saw
chain saw kickback standard" below.
Start and operate your saw without
assistance. For specific starting
instructions, see the appropriate section
of the instructionmanual. Proper starting
methods reduce the risk of injury.
6
MS 171, MS 181, MS 181 C, MS 211, MS 211 C
| Categories | Chainsaw Manuals, STIHL Chainsaw Manuals |
|---|---|
| Tags | STIHL MS 171, STIHL MS 181, STIHL MS 211 |
| Download File |
|
| Language | English, Español |
| Product Brand | STIHL. Stihl Inc, USA - Corporate phone: (757) 486-9100. International Support Information: http://stihl.com Email: info@stihl.com, Chainsaw |
| Document File Type | |
| Publisher | stihl.com |
| Wikipedia's Page | Stihl |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)