TO ENGAGE DRIVE/AUGER
WARNING: Temperature of muffler and
surrounding areas may exceed 150 F.
Avoid these areas.
1.
With the engine running near top speed, move
shift lever into one of the FORWARD or
o
REVERSE
positions.
Select
a
speed
appropriate for the snow conditions that exist.
Use the slower speeds until you are familiar
with the operation of the snow thrower.
•
•
For most efficient snow removal, remove
snow immediately after it falls.
2.
3.
Squeeze the left hand auger drive clutch to
engage auger.
Discharge
possible.
swath.
snow
Slightly
downwind
whenever
overlap
each previous
While the left hand auger drive clutch is
engaged, engage the right hand traction drive
clutch.
•
Set the skid shoes 1/4" below the scraper bar
for normal usage. The skid shoes may be
adjusted
Adjust downward when using on gravel or
crushed rock.
upward
for
hard-packed
snow.
NOTE: NEVER move shift lever without first
releasing the drive clutch.
TIRE CHAINS (OPTIONAL):
Use tire chains when extra traction is necessary.
•
•
Be certain to follow the precautions listed
under ‘‘To Stop Engine’’ in previous column
to prevent possible freeze-up.
OPERATING TIPS
Clean the snow thrower thoroughly after each
use.
NOTE: Allow the engine to warm up for a few
minutes as the engine will not develop full power
until it reaches operating temperature.
SECTION 8: ADJUSTMENTS
WARNING: Never attempt to clean
chute or make any adjustments while
engine is running.
ADJUSTING SKID SHOE
The space between the shave plate and the ground
can be adjusted by adjusting the skid shoe. Slide
the skid shoe upwards and lower the housing to
remove snow close to the ground. Slide skid shoe
downwards and raise the housing to remove snow
from uneven ground like gravel. For more details,
refer to page 11.
ADJUSTING CHUTE
You can control the distance that snow is thrown by
adjusting the angle of the chute assembly. The
sharper the angle, the shorter the distance snow is
thrown.
ADJUSTING TRACTION DRIVE CLUTCH
Refer to the Final Adjustments section on page 10
for instructions to adjust the traction drive clutch. If
you are not sure whether you have been able to
adjust the traction drive clutch properly, check as
follows.
1.
To adjust the chute, loosen the hand knob. See
Figure 25.
2.
Pivot the top of the chute assembly to the
position desired.
1.
Drain the gasoline from the snow thrower or put
a plastic film under the gas cap if the snow
thrower has already been operated. Tip the
snow thrower forward onto the auger housing.
2.
3.
Remove the frame cover underneath the snow
thrower by removing the six self-tapping screws.
With the traction drive clutch released, check if
there is clearance between the friction wheel
and the drive plate in all positions of the shift
lever. For correct adjustment there has to be
enough clearance.
Hand
Knob
4.
With the traction drive clutch engaged, check if
the friction wheel is contacting the drive plate.
See Figure 26. For correct adjustment, these
two must contact.
Figure 25
14
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals |
|---|---|
| Tags | MTD 614E, MTD E642E, MTD E644E, MTD E662H, MTD E664F, MTD Snow Blower Manual, Yard Machines 614E, Yard Machines E642E, Yard Machines E644E, Yard Machines E662H, Yard Machines E664F |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yard Machines, 614E, E642E, E644E, E662H, E664F, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)