Chute Clean-Out Tool
.
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly
during operation, proceed as follows to safely clean the
chute assembly and chute opening:
•
Release both the Auger Control and the Drive
Control.
•
•
Stop the engine by removing the ignition key.
Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
Drift
Cutter
•
Carriage Screws /
Hex Nuts
WARNING: Never use your hands to clean
snow and ice from the chute assembly or
auger housing
Figure 12
Tire Chains (on models so equipped)
•
•
Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition
key and start the snow thrower’s engine.
While standing in the operator’s position (behind
the snow thrower), engage the auger control for a
few seconds to clear any remaining snow and ice
from the chute assembly.
Tire chains should be used whenever extra traction is
needed. If your unit is not equipped with tire chains,
contact Customer Support for information regarding
price and availability.
Operating Tips
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
Drift Cutters
Drift cutters should be used when operating the snow
thrower in heavy drift conditions.
(on models so equipped)
WARNING: The temperature of the muffler
and the surrounding areas may exceed
On models so equipped, drift cutters are assembled to
the auger housing inverted. Remove the carriage bolts
by unthreading the hex nuts which secure them, and
reinstall the drift cutters in their proper position before
operating the snow thrower. See Figure 12 .
150°
F(65° C). Avoid these areas.
•
•
•
•
If possible, remove snow immediately after it falls.
Discharge snow downwind whenever possible.
Slightly overlap each previous path.
Set the skid shoes 1/4" below the shave plate for
normal usage. Adjust it upward for hard-packed
snow and downward when using on gravel or
crushed rock.
If your unit is not equipped with drift cutters, contact
Customer Support as instructed on page 2 for
information regarding price and availability.
Snow Thrower Model
Drift Cutter Kit
All models
OEM-390-679
•
Avoid possible starter freeze-up. Clean the snow
thrower thoroughly after each use.
13
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yardworks Snow Blower Manuals |
|---|---|
| Tags | MTD 60-3754-4, MTD 603753-6, MTD Snow Blower Manual, Yardworks 60 3754-4, Yardworks 603753-6 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yardworks, 60-3753-6, 60-3754-4, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(8 votes, average: 3.88 out of 5)
Lawn and Garden readers have rated Yardworks 603753-6 60-3754-4 Snow Blower Owners Manual by MTD 3.9 out of 5.0 based on 8 product reviews. lost the manual, I need another one
Just bought this machine off craigslist. Guy says it hasn't worked since last service. Can see the idler was set up wrong and it looks like the belt is the wrong size. Hopefully this manual will help diagnosis and repair.
good smowplower but can't find instructions on what oil to use and how to change the oil.
good smowplower but can't find instructions on what oil to use and how to change the oil.
Good machine but missing the manual
i have had this for 4 winters now and we get a lot of snow here works great blows snow with easy even 3 to 4 feet of snow only prob is with heavy slushy snow it tends to plug up other than that can^t say a bad word about it.i would recomend this blower to anyone
It is a good snowblower. I have had no trouble with it and I have had it for10 years
I have a model 31AE295-515 (60-3752-8) Series 1HO 21B20 775. Can you advise me as to the proper size for the belt for this model. Thank you James Maxim
I have a 28in snowblower I bought 3 years ago but I cant find a head light bulb to fit it
I have the owners manual 60-3754-4 which tells me I should change the oil every season but nowhere does it say how much oil to use, what type, where it goes or how to drain it.