4.
Lightly lubricate snowthrower with light oil and
grease as shown in Figure 22. Wipe up any
excess oil or grease.
2.
3.
4.
Clean area around pipe plug so dirt is removed.
Remove pipe plug from gear box (Fig. 24).
Check level of grease in gear box. Grease must
be visible through opening.
IMPORTANT: Do not get oil or grease on
rubber wheel or friction drive plate because
the wheel will slip and the rubber may
deteriorate.
5.
If level of grease is low, add MAG-1 grease (a
low temperature, high pressure grease, Toro part
no. 505–101) to the gear box until point of
overflow.
5.
Reinstall bottom cover with (4) screws.
Note:
Only use low temperature, high
pressure grease in gear box.
Changing Crankcase Oil
Initially, change oil after the first 2 hours of engine
operation; thereafter, under normal conditions, change
oil after every 25 hours of engine operation or
annually, whichever comes first. If possible, run
engine just before changing oil because warm oil
flows better and carries more contaminants than cold
oil.
6.
Reinstall pipe plug in gear box.
Adjusting Auger/Impeller Drive
Belt
If auger/impeller belt slips, resulting in decreased
snowthrowing performance, either an adjustment or a
new belt is required.
1.
2.
3.
Pull wire off spark plug and make sure wire does
not contact plug accidentally.
1.
Check adjustment per steps 4–6 of Install Auger
Drive Control Linkage, page 9. Make
adjustments if required.
Block up the rear of the snowthrower chassis and
remove the left wheel.
Clean area around oil drain plug. Next, slide oil
drain pan below drain extension; then remove oil
drain plug (Fig. 23).
2.
Check tension of belt by operating the auger. If
belt still slips, replace the belt. USE ONLY
GENUINE TORO REPLACEMENT PARTS.
4.
5.
After all oil is drained, reinstall oil drain plug
and left wheel.
Replacing Auger/Impeller Drive
Belt
Position snowthrower on a level surface. Next,
fill crankcase with oil: refer to Fill Crankcase
With Oil, page 10. Wipe up any oil that may
have spilled.
When auger/impeller drive belt (Fig. 25) becomes
worn, stretched, oil–soaked or otherwise damaged,
belt replacement is required.
Auger Gear Box Grease
1.
2.
3.
Pull wire off spark plug and make sure it does
not contact the plug accidentally.
The auger gear box grease level must be checked at
time of snowthrower assembly, after every 10 hours
of use and upon removal from annual storage. To
check the auger gear box grease level:
Remove (2) screws holding belt cover in place
and set cover aside (Fig. 25).
Remove auger/impeller drive belt from engine
pulley and large auger/impeller pulley (Fig. 26).
1.
Position snowthrower on a level surface.
15
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38052 |
| Model Number | 38052 |
| Model Year | 1995 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 59000001 - 59999999 |
| Product Name | 521 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 21 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HSSK50-67259N |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 4 Cycle |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)