4.
Installing the Auger/Impeller
Drive Control Linkage
1
1
Clevis pin
Cotter pin
Procedure
1.
Loosen the jam nut above the clevis on the upper
control rod (Figure 8).
Figure 9
1.
2.
Handgrip
3.
4.
1 to 2 inches (2.5 to 5 cm)
5 inches (12.7 cm)
Auger/impeller control
lever
Note: The distance should be approximately 5
inches (12.7 cm).
4.
Press the auger/impeller drive control lever slowly
toward the handgrip.
Note: The amount of force needed to compress the
lever increases noticeably when you remove the slack
from the auger/impeller drive belt (approximately
Figure 8
1/2
of the lever movement). The adjustment is
1.
Upper control rod
4.
Cotter pin
correct when the force begins to increase and the
distance between the top of the handgrip and the
bottom of the auger/impeller drive control lever is 1
to 2 inches (2.5 to 5 cm) as shown in Figure 9.
2.
3.
Jam nut
Clevis
5.
6.
Lower control rod
Clevis pin
2.
Align the holes in the clevis and the lower control
rod and insert the clevis pin (Figure 8).
Note: If the force does not noticeably increase,
remove the belt cover (refer to step 2 of Replacing
the Traction Drive Belt) and measure 2 inches (5 cm)
above the handgrip at the point where you remove
the slack from the auger/impeller drive belt.
3.
Check the distance between the top of the handgrip
and the bottom of the auger/impeller drive control
lever (Figure 9).
5.
To adjust the distance:
A. Remove the clevis pin.
B. Loosen the jam nut.
C. Thread the clevis up or down to increase or
decrease the distance between the top of the
handgrip and the bottom of the auger/impeller
drive control lever (Figure 8).
6.
7.
When the adjustment is correct, install the clevis pin
and secure it in place with the cotter pin (Figure 8).
Tighten the jam nut to secure the clevis (Figure 8).
9
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38606, Toro 38607, Toro 622R, Toro Power Max 622E |
| Model Number | 38606, 38607 |
| Model Year | 2007 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Polski, Slovenčina, Svenska |
| Serial Number | 270000001 - 270999999 |
| Product Name | Toro 622R Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | Fwd. .9 / 1.3 / 1.9 Rev. 1.3 mph |
| Engine Motor Model # | OH195SA-72566G |
| Engine Motor Size | 195cc |
| Engine Motor Type | 4 Cycle CARB2 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)