Figure 39
Figure 40
1.
2.
Primary V-belts
Belt guide
3.
Idler pulley
1.
2.
Differential cover sections
Front clutch housing
3. Right rear bearing housing
7.
Tighten the mounting screws and check the
alignment.
5.
Loosen the idler pulley mounting nut on the
differential idler pulley and pivot the idler pulley
counterclockwise away from the backside of the belt
to release the belt tension.
8.
To push or pull the machine easier without starting
the engine, adjust the belt guide (Figure 39, inset)
as follows:
6.
Remove the 2 bolts and locknuts securing the front
clutch housing to the side plate (Figure 40).
A. Engage the clutch.
B. Loosen the nut securing the idler pulley and belt
guide to the idler arm.
7.
Rotate the housing 180° so the bottom of the
housing points upward.
C. Rotate the belt guide clockwise until a gap of
approximately 0.06 inch (0.15 cm) is obtained
between the guide finger and the backside of the
drive belts.
8.
Remove the 2 bolts and locknuts securing the right
rear bearing housing to the side plate (Figure 40).
9.
Rotate the housing 180° so the bottom of the
housing points upward. Remove old belt.
D. Tighten the bolt and locknut securing the idler
pulley and belt guide to the idler arm.
10.
Slide the new belt over the rotated housing covers,
the differential cover sections, and onto the
differential pulleys.
9.
Close the cover and secure the retainer.
11.
Ensure that the idler pulley is positioned against the
backside of belt.
Replacing the Differential Belt
1.
Remove the bolts securing the traction drive and reel
drive belt covers to the right side plate and remove
the belt covers.
12. Rotate both housings back into the upright position
and secure them to the side plate with the bolts and
nuts previously removed.
2.
Loosen the idler pulley mounting nut, on each idler
pulley, and pivot each idler pulley counterclockwise
away from the backside of each belt to release belt
tension.
13. Adjust the differential belt tension; refer to Adjusting
the Differential Belt.
14.
Adjust the belt tension on the traction drive and reel
drive belts; refer to Adjusting the Traction Drive
Belt, and Adjusting the Reel Drive Belt
3.
4.
Remove the belts.
Remove the bolts securing the front and rear sections
of the differential cover to the differential housing
and slide the cover sections away to expose the belt
(Figure 40).
15. Install the differential, traction drive, and reel drive
covers.
29
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 04036, Toro 04037, Toro Greensmaster 2000, Toro Greensmaster 2600 |
| Model Number | 04036, 04037 |
| Model Year | 2011 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 311000001-311999999 |
| Product Name | Greensmaster 2000 Mower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Product Series | Toro GR 1000 Series |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)