5.
Adjust spring extension.
7. Remove hex bolts securing housing to frame. Tip
housing and frame apart on pivot pins (Figure
35).
a.With the traction drive clutch lever disengaged,
loosen the jam nut on the cable adjuster.
8.
Remove attachment drive belt from attachment
pulley (hold brake away from belt).
b.Turn the adjuster body up the cable for more
spring extension.
c.Turn the adjuster body down the cable for less
spring extension.
1
d.Finger tighten the jam nut, and then hold the
adjuster body with pliers and tighten the jam nut
with wrench.
6.
Measure the extension of the traction drive clutch
spring.
7.
8.
Repeat step 5 until traction drive clutch spring
lengthens 1/2 -11/16 in.(12.7-17.5 mm) when the
traction drive clutch lever is engaged.
With the clutch disengaged, check that there is
more than 1/32 in. (0.8 mm) clearance between
friction disc and drive plate assembly.
3
2
IMPORTANT: If spring length cannot be adjusted
1.Pivot Pin
2.
3.
Housing Cap Screws
Belt Cover
within specified range, see your Dealer for repairs.
ATTACHMENT DRIVE BELT REPLACEMENT
Remove old attachment drive belt:
OS7215
Figure 35
1.
2.
3.
Shut off engine and allow to cool completely.
2
Remove belt cover (Figure 35).
3
1
Remove hair pin under the control panel
connecting the discharge chute rod from the
chute rotation lever and slide the discharge chute
rod forward.
4
IMPORTANT: Disconnect chute lock cable and
deflector cable, if equipped.
9
4.
Remove belt finger (Figure 36).
IMPORTANT: Use care when rotating the belt fingers.
8
DO NOT bend belt fingers out of shape.
WARNING: Turning the engine sheave
may cause ACCIDENTAL ENGINE START
UP that can cause death or serious injury.
ALWAYS stop engine, remove key, wait for
moving parts to stop and remove wire from
spark plug.
7
6
5
5.
Remove attachment drive belt from engine
sheave (it may be necessary to turn engine
sheave using recoil starter handle).
1.
2.
3.
4.
5.
Traction Drive Belt
Engine Sheave
Attachment Drive Belt
Belt Finger
6.Attachment Pulley
7.Attachment Idler
Adjustment Nut
8.Traction Belt Idler
9.Traction Drive Pulley
IMPORTANT: To avoid bending bottom cover when
tipping unit apart, support handlebars firmly or tip unit
up on housing and remove bottom cover by removing
six cap screws before separating unit.
Attachment Belt Idler
OS7220
Figure 36
6.
Support Sno-Thro frame and housing.
CAUTION: Always support Sno-Thro frame
and blower housing when loosening the cap
screws holding them together. Never loosen
cap screws while unit is in service position.
GB - 29
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 926001, Ariens 926002, Ariens 926003, Ariens 926004, Ariens 926005, Ariens 926006, Ariens 926007, Ariens 926008, Ariens 926009, Ariens 926010, Ariens 926011, Ariens 926012, Ariens 926101, Ariens 926102, Ariens 926103, Ariens 926300, Ariens 926301, Ariens 926302, Ariens 926303, Ariens 926304, Ariens 926500, Ariens 926501, Ariens 926504 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)