OPERATION
Ignition Switch
WARNING: AVOID INJURY. Read and
Key Switch has two positions:
understand the entire Safety section before
2
proceeding.
1. “Stop” - pulled out
2. "Run" - pushed in
2
1
WARNING: To avoid injury to hands and feet,
always disengage clutches, shut off engine,
and wait for all movement to stop before
unclogging or working on snow thrower.
Keep hands and feet away from auger and
impeller.
NOTE: DO NOT twist key after it is
inserted.
OS1431
Ignition Switch (12V start on dash panel)
The ignition switch is operated by a
removable key. It has three positions:
1
2
CONTROLS AND FEATURES
See Figure 10 for all Controls and Features locations.
3
1.Stop
2.Run
Dual Handle Interlock
OS0232
3.Start
When Attachment Clutch and then Traction Drive
Clutch are engaged, the Attachment Clutch will remain
engaged (lever down) if released. To stop attachment,
release Traction Drive Clutch and both clutches will
disengage.
Primer Bulb
Pushing the primer bulb in adds fuel for
easier engine start. Refer to Starting and
Shut Off on page 17.
OS1321
Traction Drive Clutch - Left Hand Lever
Speed Selector
Squeeze the Traction Drive Clutch
Position the Speed Selector in the appropriate speed
notch to control forward and reverse travel.
Lever against the Handlebar (1) to
2
engage wheel drive for propelling
unit. Forward speed will vary
according to snow depth and
Forward:
6
(6) Fastest
(1) Slowest
Reverse:
(1) Slow
moisture content.
1
Release lever (2) to stop movement.
OL2701
NOTE: When traveling to or from the
area to be cleared, press down on the handlebars
enough to raise the front of the unit slightly off the
surface. Engage the traction drive clutch without
engaging the attachment drive clutch.
(2) Fast
1
IMPORTANT: DO NOT
change motion from forward
to reverse with clutch
engaged. Forward speed can
be changed without
1
2
Attachment Clutch - Right Hand Lever
Squeeze Attachment Clutch Lever
2
OS1192
against handlebar (1) to engage
attachment. Release both clutch
levers (2) to disengage power and
apply brake to attachment.
declutching.
Choke Control Knob
1. Choke Closed position: chokes off
air to engine for easier start.
1
IMPORTANT: If the belt squeals
when the attachment clutch lever is
engaged, the impeller may be frozen
in the auger housing. Immediately
2. Choke Open position: allows for
normal operation.
2
OL2691
1
release the attachment clutch lever and move the unit
into a heated area to thaw.
IMPORTANT: Gradually open choke
after engine starts.
OS1332
NOTE: If belt squeals when impeller turns freely, see
Attachment Drive Belt Replacement on page 27.
GB - 14
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 926001, Ariens 926002, Ariens 926003, Ariens 926004, Ariens 926005, Ariens 926006, Ariens 926101, Ariens 926102, Ariens 926103, Ariens 926300, Ariens 926301, Ariens 926302, Ariens 926303, Ariens 926304, Ariens 926500, Ariens 926501, Ariens 926504, Ariens 926505, Ariens ST11526DLE, Ariens ST11528LE, Ariens ST1328DLE, Ariens ST1328LE, Ariens ST1332DLE, Ariens ST1332LE, Ariens ST1336DLE, Ariens ST8526L, Ariens ST8526LE, Ariens ST926DLE, Ariens ST926LE |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)