MAINTENANCE SCHEDULE
CHECK ENGINE OIL
The engine crankcase oil should be checked every 5
hours of operation. Oil level MUST be maintained in
safe operating range on dipstick at all times or engine
damage will result (See Engine Manual).
The chart below shows the recommended
maintenance schedule that should be performed on a
regular basis. More frequent service may be required.
Park unit on a level surface. Refer to Engine Manual for
detailed instructions.
MAINTENANCE SCHEDULE
Service Performed
Each Use
Every 5
hrs.
Every 25
hrs.
Yearly
CHANGE ENGINE OIL
Check Dual Handle
Interlock
•
Change oil after first 2 hours of operation, thereafter
change oil every 25 hours (more often if required).
Refer to Engine Manual for detailed instructions.
Check Fasteners
•
•
Check Clutch
Operation
Run engine just prior to changing oil. Warm oil will flow
more freely and carry away more contamination.
Remove the oil drain plug from the rear of the unit and
tip the unit back to help drain all the oil.
Check Clutch Spring
Adjustments
*
•
•
Clean Engine
•
Check Engine Oil
Change Engine Oil
•
CHECK TIRE PRESSURE
Keep tires at pressure listed on the tire sidewall.
**
Check Tire Pressure
•
•
CHECK AUGER GEARCASE
Check Auger
Gearcase
•
IMPORTANT: Proper oil level must be maintained.
Gear cases are filled to the correct level at the factory.
Unless there is evidence of leakage, no additional
lubricant should be required. Check oil level each
season or every 25 hours of operation.
General Lubrication
•
•
•
•
Battery Maintenance
*
After first five hours of operation.
**
After first two hours of operation.
To ensure adequate lubricant level:
1.
Remove filler plug (Figure 17). Lubricant must be
at least up to bottom of lubricant filler hole with
unit resting on a level-surface.
CHECK DUAL HANDLE INTERLOCK
Without the engine running, press down (engage) both
clutch levers. Release attachment clutch lever.
Attachment clutch should remain engaged until traction
clutch lever is released, then both clutches must
disengage.
2.
Add lubricant if required. Allow oil to drain to level
of plug and replace plug.
IMPORTANT: Use only Ariens special gear lubricant
L-2 (Part Number 00008000). Gearcase filler plug may
require an application of Loc-Tite® 565 thread sealant
with repeated servicing.
CHECK FASTENERS
Make sure all hardware is tightened properly.
CHECK CLUTCH OPERATION
Auger / impeller must stop within 5 seconds when
attachment clutch/impeller brake lever is released.
1
3
Wheels must stop quickly when traction drive clutch
lever is released.
If clutches do not engage or disengage properly, adjust
or repair before operation (see SERVICE AND
ADJUSTMENTS on page 22).
CHECK CLUTCH SPRING ADJUSTMENT
Make sure the attachment clutch and traction drive
clutch are adjusted to the range specified in
Attachment Clutch/Brake Adjustment on page 25.
2
1.Auger Gearcase - Cast Iron
Oil Fill and Drain Plug
Auger Gearcase - Aluminum
2.
3.
CLEAN ENGINE
Refer to Engine Manual for detailed instructions.
Figure 17
OS7130
GB - 20
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 926001, Ariens 926002, Ariens 926003, Ariens 926004, Ariens 926005, Ariens 926006, Ariens 926101, Ariens 926102, Ariens 926103, Ariens 926300, Ariens 926301, Ariens 926302, Ariens 926303, Ariens 926304, Ariens 926500, Ariens 926501, Ariens 926504, Ariens 926505, Ariens ST11526DLE, Ariens ST11528LE, Ariens ST1328DLE, Ariens ST1328LE, Ariens ST1332DLE, Ariens ST1332LE, Ariens ST1336DLE, Ariens ST8526L, Ariens ST8526LE, Ariens ST926DLE, Ariens ST926LE |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)