5.
Adjust spring extension.
1
a.With the traction drive clutch lever disengaged,
loosen the jam nut on the cable adjuster.
b.Turn the adjuster body up the cable for more
spring extension.
c.Turn the adjuster body down the cable for less
spring extension.
d.Finger tighten the jam nut, and then hold the
adjuster body with pliers and tighten the jam nut
with wrench.
6.
Measure the extension of the traction drive clutch
spring.
3
2
7.
8.
Repeat step 5 until traction drive clutch spring
lengthens 1/2 -11/16 in.(12.7-17.5 mm) when the
traction drive clutch lever is engaged.
1.Pivot Pin
2.
3.
Housing Cap Screws
Belt Cover
With the clutch disengaged, check that there is
more than 1/32 in. (0.8 mm) clearance between
friction disc and drive plate assembly.
OS7215
Figure 33
IMPORTANT: If spring length cannot be adjusted
within specified range, see your Dealer for repairs.
2
3
1
ATTACHMENT DRIVE BELT REPLACEMENT
Remove old attachment drive belt:
4
1.
2.
3.
Shut off engine and allow to cool completely.
Remove belt cover (Figure 33).
9
Remove hair pin under the control panel
connecting the discharge chute rod from the
chute rotation lever and slide the discharge chute
rod forward.
8
IMPORTANT: Disconnect chute lock cable and
deflector cable, if equipped.
4.
Remove belt finger (Figure 34).
IMPORTANT: Use care when rotating the belt fingers.
DO NOT bend belt fingers out of shape.
7
5.
Remove attachment drive belt from engine
sheave (it may be necessary to turn engine
sheave using recoil starter handle).
6
5
1.
2.
3.
4.Belt Finger
5.Attachment Belt Idler
Traction Drive Belt
Engine Sheave
Attachment Drive Belt
6.Attachment Pulley
7.Attachment Idler
Adjustment Nut
8.Traction Belt Idler
9.Traction Drive Pulley
IMPORTANT: To avoid bending bottom cover when
tipping unit apart, support handlebars firmly or tip unit
up on housing and remove bottom cover by removing
six cap screws before separating unit.
6.
Support Sno-Thro frame and housing.
OS7220
Figure 34
CAUTION: Always support Sno-Thro frame
and blower housing when loosening the cap
screws holding them together. Never loosen
cap screws while unit is in service position.
7.
8.
Remove hex bolts securing housing to frame
(three on each side). Tip housing and frame apart
on pivot pins (Figure 33).
Remove attachment drive belt from attachment
pulley (hold brake away from belt).
GB - 27
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 926001, Ariens 926002, Ariens 926003, Ariens 926004, Ariens 926005, Ariens 926006, Ariens 926101, Ariens 926102, Ariens 926103, Ariens 926300, Ariens 926301, Ariens 926302, Ariens 926303, Ariens 926304, Ariens 926500, Ariens 926501, Ariens 926504, Ariens 926505, Ariens ST11526DLE, Ariens ST11528LE, Ariens ST1328DLE, Ariens ST1328LE, Ariens ST1332DLE, Ariens ST1332LE, Ariens ST1336DLE, Ariens ST8526L, Ariens ST8526LE, Ariens ST926DLE, Ariens ST926LE |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)