MTD Cub Cadet 1345 SWE 45-Inch Snow Blower Owners Manual

Remove the shear bolts on the auger shaft.
Oil or spray lubricant inside shaft.
Carefully spin the auger around by hand to
disperse the lubricant.
Reinstall the shear bolts.
Traction Control / Auger Control Lock
The cams on the ends of the control rods which
interlock the traction drive and auger drive clutches
must be lubricated at least once a season or every 25
hours of operation using a multi-purpose automotive
grease. The cams can be accessed beneath the handle
panel as shown in Figure 15.
Lube Under Chute Base
Chute Crank Spirals
Handle Panel
Figure 14
Discharge Chute
The base of the discharge chute and the spirals on the
chute crank should be lubricated at least every 25
hours of use. When applying the lubrication, apply the
lubricant as shown in Figure 14 to the point under the
base of the chute and where the spirals contact the
discharge chute.
Drive and Shifting Mechanism
Lube Cams Here
Control Rods
At least once a season or after every 25 hours of
operation, remove rear cover. Lubricate any chains,
sprockets, gears, bearings, shafts, and the shifting
mechanism at least once a season. Refer to Figure 11.
Use engine oil or a spray lubricant. Avoid getting oil on
rubber friction wheel and aluminum drive plate.
Figure 15
Check V-Belts
Follow the instructions below to check the condition of
the drive belts every 50 hours of operation.
Gear Case
Remove the plastic belt cover on the front of the
engine by removing the three self-tapping screws.
Visually inspect for frayed, cracked, or excessively
worn out belts.
Replace belts as necessary as outlined in Section
7.
The gear case is lubricated with grease at the factory
and does not require initial checking. If disassembled
for any reason, lubricate with two ounces of Shell
Alvania grease EPR00, part number 737-0168.
Before reassembling, remove old sealant and apply
Loctite 5699 or equivalent.
Check Friction Wheel Rubber
Follow the instructions below to check the condition of
the friction wheel rubber every 25 hours of operation.
To check the level of grease in the gear case, remove
the vent plug as shown in Figure 13. If necessary, add
grease using a grease gun and the grease fitting on the
side of the gear case.
Remove the six self-tapping screws from the frame
cover underneath the snow thrower.
Visually inspect the friction wheel rubber for
excessive wear, cracks, or loose fit on the friction
wheel drive hub.
IMPORTANT: Do not overfill the gear case. Be sure the
vent plug is free of grease in order to relieve pressure.
Auger Bearings and Shaft
Every season lubricate the auger bearings and the
bearings on the side of the frame with light oil. Refer to
Figure 13.
Also engage the traction control and check if the
friction wheel is making contact with the friction
plate.
If it does not make contact, adjust the traction drive
cable following instructions and recheck the friction
wheel.
Use oil or spray lubricant into the bearings at the
wheels at least once a season. Remove the wheels,
one side at a time, and clean and coat axles with multi-
purpose automotive grease.
Replace friction wheel rubber if necessary. Refer to
instructions in Section 7.
Lubricate the auger shaft at least once a season. To do
this:
13
Product Specification
CategoriesCub Cadet Snow Blower Manuals, MTD Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website