MTD Cub Cadet 826 SWE 1130 SWE Snow Blower Owners Manual

If not already attached, slip the cables that run from
the handle panel to the chute into the cable guide
located on top of the engine. See Figure 4.
Cable Guide
Figure 4
“Z” End
Jam Nut
Final Adjustments
Auger Control Adjustment
Check the adjustment of the auger control as follows:
Push forward on the auger control (Refer to Figure
7) until the small rubber bumper contacts the upper
handle. There should be slack in the cable. See
Figure 5.
Auger Control Cable
Release the auger control. The cable should be
straight. Make certain you can depress the auger
control against the left handle completely without
using excess force.
Figure 5
Loosen the jam nut on the traction control cable
(located opposite the auger control cable) and
UNTHREAD the cable one full turn.
Recheck the adjustment.
Retighten the jam nut to secure the cable when the
correct adjustment is reached.
If adjustment is necessary, proceed as follows:
Loosen the jam nut and thread the cable in (for less
slack) or out (for more slack) as necessary. See
Figure 5.
If the machine can be moved freely both forward and
rearward with the traction control fully depressed,
proceed as follows:
Recheck the adjustment before retightening the
jam nut against the cable.
Traction Control and Shift Lever Adjustment
To check the adjustment of the traction control and shift
lever, proceed as follows:
Loosen the jam nut on the traction drive cable and
THREAD the cable in one full turn.
Recheck the adjustment and repeat the adjustment
as necessary.
Retighten the jam nut to secure the cable when the
correct adjustment is reached.
Move the shift lever into the sixth (6) position.
a.   With the traction control (see Figure 7)
released, push the snow thrower forward,
then pull it back. Disregarding the overall
weight of the snow thrower, the machine
should otherwise move freely.
b.   Engage the traction control, and attempt to
move the machine both forward and
rearward. You should experience resistance
as the wheels should not be turning.
NOTE: If you are uncertain that you have reached the
correct   adjustment,   refer   to   the   Traction   Control
Adjustment in Section 6 of this manual.
Skid Shoe Adjustment
The space between the shave plate and the ground can
be adjusted by repositioning the skid shoes found on
either side of the snow throwers auger housing. For
smooth surface snow removal such as on an asphalt
driveway, place the skid shoes in a lower position. Use
a higher position when the area to be cleared is
uneven. See Figure 6.
Move the shift lever into the fast reverse (R2)
position and repeat the previous steps (a & b).
If you experienced resistance either when repositioning
the shift lever (see Figure 7) from position 6 to R2 or
when attempting to move the machine forward or
rearward with the traction control released, your snow
thrower’s traction control is in need of adjustment and
you should NOT operate the snow thrower before
completing the adjustment as follows:
IMPORTANT: When operating your snow thrower on a
gravel driveway, ALWAYS adjust the skid shoes into
the HIGHEST position.
6
Product Specification
CategoriesCub Cadet Snow Blower Manuals, MTD Snow Blower Manuals, Snow Blower Manuals
Tags, , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website