•
Remove the large shoulder bolt and washer on the
left hand side of the engine pulley. See Figure 19.
•
Place the new auger belt in the pulley groove.
Position the pulley and belt inside the belt keepers
on the rear of the auger housing. See Figure 21.
Engine Pulley
Brake Bracket
Assembly
Auger Belt
Idler
Pulley
Belt
Keepers
Auger
Pulley
Shoulder
Bolt
Hex Screw, &
Belleville Washer
Figure 19
Auger Belt
Figure 21
NOTE: Reference to right hand or left hand side of the
•
•
Align the keyway of the pulley with the hi-pro key,
lift the brake bracket assembly, and push the pulley
fully onto auger gear box input shaft. Secure with
the hex screw and belleville washer (cupped side
toward the pulley). The brake puck must be seated
in the pulley groove.
Insert the ferrule on the auger idler rod into the
brake bracket assembly and secure with the flat
washer and internal cotter pin. Check for proper
adjustment.
machine are observed from the operating position.
•
Remove the internal cotter pin and flat washer from
the ferrule in order to disconnect the auger idler rod
from the brake bracket assembly. See Figure 20.
Slip the auger drive belt (the front belt) off the
engine pulley. See Figure 20.
•
•
Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable “Z” fitting.
Engine
Pulley
Auger Drive
Belt
Proper Adjustment: With the auger clutch lever in the
disengaged position, the top surface of the new belt
should be even with the outside diameter of the pulley.
Auger
Idler Rod
Internal
•
To adjust, remove the auger idler arm ferrule from the
brake bracket and thread the ferrule in (towards idler
pulley) to increase tension on belt, or out to decrease
tension.
Cotter Pin/
Flat Washer
Ferrule
Brake Bracket
Assembly
NOTE: The brake puck must always be firmly seated in
Cable Roller
the pulley groove when auger control is disengaged.
Guide
Z Fitting
•
If also replacing the drive belt, proceed to the "Drive
Belt" instruction. If not, reassemble the two halves
of the unit hooking the lower portion of the auger
housing over the stationary shoulder bolts in the
frame assembly.
Figure 20
•
•
•
Use a 9/16” wrench to remove the upper bolts and
lock washers that secure the rear of the auger
housing to the frame . Refer to Figure 18.
Separate the auger housing from the frame by
tilting the housing forward and pulling up the
handles.
Using a 1/2” wrench, remove the hex screw and
belleville washer from the center of the pulley on
the auger housing. Lift the brake bracket assembly
out of the pulley groove and remove the pulley. Be
careful not to lose the hi-pro key from the center of
the pulley. See Figure 21.
•
•
Secure the two halves with the two bolts and lock
washers removed earlier.
Pull the brake bracket assembly toward the left side
of the frame and re-insert the ‘Z’ fitting of the auger
idler cable.
Reinstall the shoulder bolt and lock washer on the
left side of the engine pulley, and reinstall the belt
cover.
Position the chute crank rod and reinstall the flat
washer and internal cotter pin.
•
•
16
| Categories | Cub Cadet Snow Blower Manuals, MTD Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Cub Cadet 928 SWE, Cub Cadet 933 SWE, Cub Cadet 945 SWE, MTD 928 SWE, MTD 933 SWE, MTD 945 SWE, MTD Snow Blower Manual |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)