OIL AND FUEL INFORMATION
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:
1.
2.
Remove the fuel cap
(Fig. 10).
Place the gas
•
•
•
Always use fresh unleaded gasoline
Use the fuel additive STA-BIL® or an equivalent
Drain tank and run the engine dry before storing unit
container’s spout
into the fill hole on
the fuel tank (Fig. 10)
and fill the tank.
NOTE: Do not overfill
the tank.
Gas Can
Spout
Fuel Cap
Fuel Tank
Using Fuel Additives
Fig. 10
The use of fuel additives, such as STA-BIL® Gas Stabilizer or an
equivalent, will inhibit corrosion and minimize the formation of gum
deposits. Using a fuel additive can keep fuel from forming harmful
deposits in the carburetor for up to six (6) months. Add 0.8 oz. (23 ml.)
of fuel additive per gallon of fuel according to the instructions on the
container. NEVER add fuel additives directly to the unit's gas tank.
WARNING:
Gasoline is extremely flammable. Ignited
vapors may explode. Always stop the engine and allow it to
cool before filling the fuel tank. Do not smoke while filling the
tank. Keep sparks and open flames at a distance from the area.
WARNING:
3.
4.
5.
Wipe up any gasoline that may have spilled.
Reinstall the fuel cap.
Move the unit at least 30 ft. (9.1 m) from the fueling source and
site before starting the engine.
Add fuel in a clean, well ventilated
outdoor area. Wipe up any spilled fuel immediately.
Avoid creating a source of ignition for spilt fuel. Do not
start the engine until fuel vapors dissipate.
NOTE: Dispose of the old gasoline in accordance to Federal, State
and Local regulations.
FUELING THE UNIT
WARNING:
vapors may explode. Always stop the engine and allow it to
cool before filling the fuel tank. Do not smoke while filling the
tank. Keep sparks and open flames at a distance from the area.
Gasoline is extremely flammable. Ignited
STARTING AND STOPPING INSTRUCTIONS
STOPPING INSTRUCTIONS
WARNING:
Operate this unit only in a well-ventilated
outdoor area. Carbon monoxide exhaust fumes can be
lethal in a confined area.
1.
Release your hand from the throttle control. Allow the engine to
cool down by idling.
2.
Put the On/Off Stop Control in the OFF (O) position.
WARNING:
Avoid accidental starting. Make sure you are
Stop/ Off (O)
Start/ On (I)
in the starting position when pulling the starter rope (Fig. 13).
To avoid serious injury, the operator and unit must be
in a stable position while starting.
Make sure that any Add-On item is installed correctly
and secure before starting the unit.
Throttle Control
STARTING INSTRUCTIONS
Fig. 11
1.
2.
3.
4.
Check the oil level in the crankcase. Refer to Checking the Oil
Choke Lever
Postition 1
Level.
Primer Bulb
Fill the fuel tank with fresh, clean unleaded gasoline. Refer
to Fueling the Unit.
Make sure the On/Off Stop Control in the ON ( I ) position
(Fig. 11).
Fully press and release the primer bulb 10 times, slowly.
Some amount of fuel should be visible in the primer bulb
and fuel lines (Fig. 12). If you can’t see fuel in the bulb,
press and release the bulb as many times as it takes
before you can see fuel in it.
Fig. 12
Starter Rope
5.
6.
Place the choke lever in Position 1 (Fig. 12).
Crouch in the starting position (Fig. 13), squeeze the
throttle control, and pull the starter rope briskly 5 times.
7.
8.
Place the choke lever in Position 2 (Fig. 14).
While squeezing the throttle control, pull the starter rope
briskly 1 to 4 times to start the engine.
Throttle
Control
9.
Keep the throttle squeezed and allow the engine to warm
up for 15 to 30 seconds.
Fig. 13
10.
Place the choke lever in Position 3 (Fig. 14). The unit is
ready for use.
Position 2
Position 3
IF... the engine does not start, go back to step 4.
IF... the engine fails to start after a few attempts, place the
choke lever in Position 3 and squeeze the throttle control.
Pull the starter rope briskly 3 to 8 times. The engine
should start. If not, repeat.
IF WARM... If the engine is already warm, make sure the
On/Off Stop control is in the ON position and start the unit
with the choke lever in Position 2. After the unit starts,
move the choke lever to Position 3.
Fig. 14
5
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, MTD Trimmer Manuals, Trimmer Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD TB415CS, MTD TB465SS, Troy Bilt TB465SS, Troy-Bilt TB415CS |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)