MTD Troy-Bilt Zero Turn Tractor RZT 50 W Inch Deck Lawn Mower Owners Manual

TABLE OF CONTENTS
TRACTOR PREPARATION  ...................................................................................................  2
IMPORTANT SAFE OPERATION PRACTICES  ....................................................................  4
SAFETY DECALS AND LABELS ...........................................................................................  7
RECORDING MODEL AND SERIAL NUMBER INFORMATION ...........................................  9
CUSTOMER SUPPORT .........................................................................................................  9
SLOPE GAUGE ....................................................................................................................  10
SECTION 1: CONTROLS AND FEATURES ........................................................................  11
SECTION 2: OPERATION  ...................................................................................................  15
SECTION 3: ADJUSTMENTS ..............................................................................................  22
SECTION 4: MAINTENANCE  ..............................................................................................  23
SECTION 5: MOWER DECK  ...............................................................................................  28
WARRANTIES.......................................................................................................................  35
TRACTOR PREPARATION
Remove the upper crating material from the shipping
pallet, and cut any bands or tie straps securing the trac-
tor to the pallet.
Use the seat adjust lever to adjust the seat position. Re-
fer to "Adjusting the Operator’s Seat"  in Section 3 for
seat adjustment instructions.
Use the lift handle to raise the deck to its highest posi-
tion;  engage  the  transmission  bypass  rods  (Refer  to
SECTION 1, CONTROLS AND FEATURES); and care-
fully roll the tractor off the shipping pallet. Disengage the
bypass rods.
Seat
Adjustment
Seat
Slots
Pivot
Bracket
Seat
Adjust
Spacer
INSTALL THE OPERATOR’S SEAT
The operator’s seat was partially inserted into the seat
pivot bracket for shipping purposes. To install the seat
proceed as follows:
1.
Cut any straps securing the seat assembly and the
drive control levers. Remove any packing material.
NOTE: The seat is partially inserted into the slots of the
seat pivot bracket. If the seat does not disengage the
pivot  bracket  when  removing  the  packaging  material,
the seat may be pushed into place as described in steps
2 and 6. If the seat disengages the pivot bracket, install
the seat as instructed in steps 2 through 6.
Front/Left
Seat Adjust
Lever
Shoulder Bolt
Stop Bracket
Figure 1  
2.
Pivot the seat pivot bracket partially upward. Refer
to Figure 1.
POSITION DRIVE CONTROL LEVERS
3.
Note   the  grooves   in   the  seat   adjust   spacers
attached to the bottom of the seat, then lift the seat
and  position  above  and  to  the  rear  of  the  pivot
bracket.
The tractor’s drive control  levers are lowered for ship-
ping purposes. The flange lock nut, hex screw, and flat
washer used to secure each control lever to its pivot
bracket are removed and installed in the slotted hole of
each control lever for shipment. The control levers must
be repositioned and secured to the pivot brackets. Re-
position the control levers as follows:
4.
Align the grooves in the seat adjust    spacers with
the  sides   of  the  adjustment   slots  in   the  pivot
bracket.
5.
6.
Slide the seat adjust spacers into the slots of the
pivot bracket.
Continue  to  push  the  seat  forward   in  the  pivot
bracket until the front/left shoulder bolt of the seat
assembly  passes  forward  of the  stop  bracket  on
the seat pivot bracket. See Figure 1.
Remove the hex screw, flat washer, and flange lock
nut from the slot of one of the drive control levers.
Lift and swing that control lever upward until the
slotted hole in the lever bracket aligns with one of
the holes in the pivot bracket. Refer to Figure 2.
2
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website