MTD Troy-Bilt Zero Turn Tractor RZT 50 W Inch Deck Lawn Mower Owners Manual

Slide the flat washer onto the hex screw. From the
outside, insert the hex screw w/washer through the
control lever slot and the hole of the pivot bracket.
Secure with the flange lock nut. See Figure 2.
Align the holes of the bumper with the holes in the
tractor frame and re-insert the clevis pins through
the holes on both sides of the tractor. Install the
internal cotter pins into the clevis pins to secure.
Flange Lock Nut
Control Lever
CONNECT THE BATTERY
WARNING:  Battery   posts,  terminals  and
related accessories contain lead and lead
compounds. Wash hands after handling.
Lift control
lever upward
Flat Washer
Hex Screw
The tractor is shipped with an activated sealed battery,
with the positive battery cable factory connected. The
negative cable must be connected.
Pivot
Bracket
NOTE: Make sure the ignition switch is in the "OFF" po-
sition before attaching the battery cable.
Slotted
Hole
1.
2.
Pull the protective cap, if present, off the negative
terminal  of  the  battery,  and  remove  the  hex  cap
screw and nut from the free end of the negative bat-
tery cable.
Connect the negative battery cable (heavy black)
to negative terminal (NEG) of the battery using the
hex  cap  screw  and  nut.  Slide  the  black  terminal
cover over the negative terminal of the battery.
Figure 2  
Note the relative position of the control lever to the
pivot bracket, then repeat the previous steps to
reposition the other control lever in approximately
the same  position.
Refer to "Adjusting the Drive Control Levers" in
Section 3 for instructions on final adjustment of the
levers.
LOWER THE DECK DISCHARGE CHUTE
POSITION THE REAR BUMPER
WARNING: Never operate the mower deck
without the discharge chute installed and
in the down position.
For shipping purposes the rear bumper is rotated up-
ward  from  its  normal  position.  To  reposition  the  rear
bumper, refer to Figure 3 and proceed as follows:
NOTE: The discharge chute on the mower deck may be
held up with a chute stop shipping brace, or it may be
held up by a cable tie. If shipped with the shipping brace,
remove as described below. If held with a cable tie, cut
the cable tie and lower the discharge chute.
From inside the tractor frame, just behind the rear
tires, remove the internal cotter pins from the clevis
pins securing the bumper to each side of the frame.
While supporting the rear bumper, cut the cable tie
fastening the bumper to the engine lift bracket, and
remove the clevis pins from each side.
Remove the bumper and reposition to align the
notch at each end of the bumper with the spacer on
each side of the frame. Slide the bumper notches
onto the spacers.
Locate the shipping brace between the chute deflector
and the cutting deck. Holding the chute deflector fully
upward, remove the shipping by grasping it and rotating
it clockwise. Lower the chute deflector.
Chute Deflector
Notch
Shipping Brace
Clevis Pin
Internal
Spacer
Cotter Pin
Figure 3  
3
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website