MTD Troy-Bilt Zero Turn Tractor RZT 50 W Inch Deck Lawn Mower Owners Manual

ADJUSTING THE GAUGE WHEELS
DECK MAINTENANCE
The cutting height of the mower deck can be set in
any of six height settings using the deck lift handle of
the tractor. The deck heights range from 1-1/2 inches
to 4 inches. The deck gauge wheel position should be
approximately 1/4 to 1/2 inch above the ground when
the deck is set in the desired height setting.
Using the Deck Wash System
WARNING:  When  using  the   deck  wash
system, never engage the deck from any
position other than the operator’s seat of
the  tractor.  Do  not  use  an  assistant  or
engage   deck  in   the   presence   of   any
bystanders.
WARNING:  Keep  hands   and  feet  away
from   the    discharge   opening    of   the
cutting deck.
Attach  the  nozzle  adapter  to  a  standard  garden
hose connected to a water supply.
NOTE:  The  deck  gauge   wheels  are  an  anti-scalp
feature of the deck and are not designed to support the
weight of the cutting deck.
Move  the  tractor  to  an  area  within  reach  of  the
hose where the dispersal of wet grass clippings is
not  objectionable  to  you.  Disengage   the  PTO,
engage the parking brake, and stop the engine.
Using  the  lift  handle,  set   the  deck  in  the  desired
height  setting,  then  check  the  gauge  wheel  and  if
necessary adjust as follows.
Pull back the lock collar of the nozzle adapter and
push  the  adapter  onto   one  of  the  deck  wash
nozzles at either end of the mower deck. Release
the lock collar to lock the adapter on the nozzle.
See Figure 35.
With the deck set at the desired height, visually
check  the  distance  between  the  gauge  wheels
and the ground. If the gauge wheels are near or
touching the ground, they should be raised. If the
gauge  wheels   are  more  than   1/2"  above   the
ground, they should be lowered.
Pull Lock
Nozzle
Collar Back
Adapter
Remove the lock nut securing one of the gauge
wheel shoulder screws to the deck. Remove the
gauge wheel and shoulder screw. See Figure 34.
Adapter
Lock Collar
Insert  the  shoulder  screw  into  the  one  of  four
index holes in the front gauge wheel bracket that
will  give   the  gauge   wheel  a  1/4   to  1/2   inch
clearance with the ground.  
Deck Wash
Nozzle
Note  the  index  hole  of  the  just  adjusted  wheel,
and   adjust  the   other   gauge  wheels   into   the
respective index holes on the other gauge wheel
brackets on the deck.
Figure 35  
Turn on the water supply.
From the tractor operator’s seat, start the engine
and  engage  the  PTO.  Allow  to  run  as  needed.
Disengage the PTO and stop the engine.
Shoulder
Screw
Front Gauge
Gauge
Wheel
Turn off the water supply.
Rear Gauge
Wheel
Wheel
Bracket
Pull back  the lock collar of the  nozzle adapter to
disconnect the adapter from the nozzle.
Adjustment
Index
Repeat  the   previous  steps  to   clean  the  deck
using the nozzle at the other end of the deck.
Lock Holes
Nut
Lock
Nut
Gauge
Wheel
Shoulder
Cleaning the Spindle Pulleys
Bracket
Screw
Once a month remove the belt covers to remove any
accumulation  of   grass   clippings  from   around  the
spindle  pulleys  and  V-belt.  Clean  more  often  when
mowing tall, dry grass.
Figure 34  
31
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website