Removal (Fig. 6)
3. Install elbow (pressure), pressure tee fitting, and
pressure dampener to pump outlet. Orientate elbow to-
ward right side of machine (Fig. 7).
IMPORTANT: Make sure to neutralize and remove
chemicals from pump and hoses before loosening
and removing spray system components.
4. Remove set screws (item 16) from PTO driveshaft.
Clean threads of set screws and set screw threads in dri-
veshaft.
1.
gage parking brake, and remove key from the ignition
switch.
Park machine on a level surface, stop engine, en-
5. Apply anti–seize lubricant to pump shaft. Position
square key in pump shaft and slide PTO driveshaft fully
onto pump shaft.
2.
28)
Loosen hose clamp that secures suction hose (item
to hosebarb (item 25). Pull suction hose from hose-
barb.
6. Apply Loctite #242 (or equivalent) to threads of set
screws. Install set screws into PTO drive shaft to secure
PTO shaft to pump shaft.
3.
(item 11) to hosebarb (item 8). Pull pressure hose from
hosebarb.
Loosen hose clamp that secures pressure hose
7. Position pump drive shrouds (item 13) to shroud
bracket (item 14). Install four (4) flange head screws and
flange nuts to secure shrouds to bracket.
4.
Remove PTO driveshaft (item 17) from output shaft
of transaxle PTO assembly.
8.
head screws and flange nuts to pump and mount brack-
et. Secure pump to mount bracket.
Position pump on pump mount bracket. Install flange
5.
that secure pump assembly to pump mount bracket.
Remove four (4) flange head screws and flange nuts
6.
drive shrouds attached) from machine.
Remove pump assembly (with PTO driveshaft and
9.
PTO assembly.
Attach PTO driveshaft to output shaft of transaxle
7.
that secure pump drive shrouds (item 13) to shroud
bracket (item 14). Remove pump drive shrouds.
Remove four (4) flange head screws and flange nuts
10.Install
tings. Secure hoses with hose clamps.
pressure and suction hoses to correct barb fit-
8.
Loosen two (2) set screws (item 16) that secure PTO
1
drive shaft to pump shaft. Separate PTO drive shaft from
pump. Locate and remove key from pump shaft.
9.
nents from pump using Figure 6 as a guide. Discard any
removed o–rings and gaskets.
As needed, remove pressure and suction compo-
Installation (Fig. 6)
2
NOTE: Coat all o–rings with vegetable oil before instal-
lation to reduce the chance of damage during assembly.
1.
Apply thread sealant to threads of pressure tee fit-
ting, elbow (pressure), and suction tee fitting. Position
new o–rings and gaskets on suction and pressure fit-
tings that were removed during disassembly.
Figure 7
1.
Elbow (pressure)
2. Suction hose
2.
pump inlet. Orientate tee toward right side of machine
(Fig. 7).
Install suction tee fitting and suction dampener to
Workman 200 Spray System
Spray System
Page 3 – 11
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 200 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)