Toro 05137SL Rev A Service Manual Pro Sweep 5200 Service Manual

5.
trieve brush assembly.
After raising hopper and placing lift cylinder stop, re-
8.  Place  coupler  spider  into  coupling jaw  on  brush
shaft.
6.
to brush  shaft. Slide coupling  jaw from brush.  Locate
and retrieve square key from brush shaft.
Loosen set screws (item 14) that secure coupling jaw
9.  Install hydraulic brush motor to  brush housing (see
Hydraulic Brush  Motor Installation  in the Service  and
Repairs section of Chapter 3 – Hydraulic System). Make
sure that coupling jaws have a gap between coupler jaw
valleys from .830” to .930” (21.1 to 23.6 mm). Apply Loc-
tite  #242  (or  equivalent)  to  threads of  coupling  set
screws. Secure coupling jaws to motor shaft and brush
shaft by torquing set screws from 125 to 155 in–lb (14.1
to 17.5 N–m) (Fig. 7).
7.
To remove bearing from brush shaft:
A.  Loosen set screw that  secures locking collar to
shaft.
NOTE:  Normal  brush   rotation   is   clockwise   as
viewed from left side of sweeper.
1
B.  Using a punch and hammer, rotate locking collar
in the opposite direction of normal brush rotation to
loosen collar.
C. Slide bearing flanges, locking collar and bearing
from brush shaft.
8.
Disassemble brush using Figure 6 as a guide.
6
Installation (Fig. 5)
1.
2.
shaft. Slide bearing flanges, bearing and locking collar
to each end of brush shaft. Do not tighten set screw in
locking collar.
Assemble brush using Figure 6 as a guide.
5
3
2
4
Clean brush  shaft and apply  antisieze lubricant  to
Figure 6
1.
2.
3.
Brush
Flange nut (4 used)
Brush drive (2 used)
4.
5.
6.
Retaining ring (4 used)
Carriage screw (4 used)
Brush axle
3.
Position square key in brush shaft. Slide coupling jaw
onto drive end of brush shaft.
5
3
4.
5.
brush housing (see Servicing the Brush Housing in this
section).
Position brush assembly under raised hopper.
Antisieze
Lubricant
Slowly lower hopper  to position brush assembly to
4
3
2
1
6.
Secure bearing flanges  to brush housing  with car-
riage bolts (item 7), flat washers (item 16) and lock nuts
(item 17). Center brush in brush housing.
Antisieze
Lubricant
6
NOTE:  Normal brush rotation  is clockwise as  viewed
7
from left side of sweeper.
125
(14.1 to 17.5 N–m)
to 155 in–lb
Loctite #242
7.
Using a punch and hammer, rotate locking collar in
the direction of  normal brush rotation to tighten  collar.
Apply  Loctite #242  (or  equivalent) to  set  screw  and
torque set  screw from  125 to 155  in–lb (14.1  to 17.5
N–m) to secure locking collar to brush shaft.
Figure 7
1.
2.
3.
4.
Hydraulic brush motor
Key
5.
6.
7.
Brush
Square key
Coupling jaw
Coupling spider
Set screw (2 per jaw)
Pro Sweep 5200
Page 5 – 9
Chassis
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 77 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website