Removal (Fig. 10)
Position sweeper on a level surface with dump hop-
per empty and lowered. Have sweeper attached to tow-
ing vehicle, engage vehicle parking brake, stop engine
and remove key from the ignition switch. Chock sweep-
er wheels to prevent sweeper from moving.
Installation (Fig. 10)
1.
1. Clean roller shaft ends and apply antisieze lubricant
to shaft ends. Place adjustment plate, bearing flanges,
bearing and locking collar onto each end of roller shaft.
Do not tighten set screws in locking collars.
2.
Secure bearing flanges to roller adjustment plate
2.
roller scraper to roller adjustment plates. Remove roller
scraper from machine.
Remove flange nuts and carriage screws that secure
with carriage screws (item 13), flat washers (item 11)
and lock nuts (item 10).
3.
4.
Position roller assembly under raised hopper.
IMPORTANT: When fully lowered, the sweeper is
supported by the roller. To service the roller, raise
the sweeper slightly before carefully loosening fas-
teners that secure roller assembly.
Slowly lower hopper to position roller assembly to
housing (see Servicing the Brush Housing in this sec-
tion).
5.
Secure adjustment plates and adjuster keys to brush
housing with carriage screws and flange nuts using
location noted during removal.
CAUTION
6.
Center roller between bearings.
To prevent personal injury, make sure that roll-
er is supported as it is removed from the ma-
chine. Roller weighs approximately 80 pounds
NOTE: Normal roller rotation is counter–clockwise as
viewed from left side of sweeper.
(36.3
kg).
7.
the direction of normal roller rotation to tighten collars.
Using a punch and hammer, rotate locking collars in
3.
4.
Support roller to prevent it from shifting.
Note location of roller adjustment plates and adjuster
8. Apply Loctite #242 (or equivalent) to threads of set
screws (item 8). Install set screws into collars and torque
from 125 to 155 in–lb (14.1 to 17.5 N–m) to secure lock-
ing collars to roller shaft.
keys for reassembly purposes.
5.
plates and adjuster keys to brush housing.
Remove flange nuts that secure roller adjustment
9.
ists.
Check that roller is free to rotate and no binding ex-
6.
procedure to remove roller assembly from brush hous-
ing.
Refer to Brush Housing Service in this section for
10.Position roller scraper to machine. Install carriage
screws and flange nuts that secure roller scraper to roll-
er adjustment plates.
7.
trieve roller assembly.
After raising hopper and placing lift cylinder stop, re-
11.
adjust if necessary (see Operator’s Manual).
Check roller height and roller scraper clearance and
8.
To remove bearings from roller:
A. Remove set screw (item 8) that secures locking
collar to roller shaft.
NOTE: Normal roller rotation is counter–clockwise
as viewed from left side of sweeper.
B. Using a punch and hammer, rotate locking collar
(item 7) in the opposite direction of normal roller rota-
tion to loosen collar.
C. Remove carriage screws (item 13), flat washers
(item 11) and lock nuts (item 10) that secure bearing
flanges to roller adjustment plate.
D. Slide bearing flanges, locking collar and bearing
from roller.
Pro Sweep 5200
Page 5 – 13
Chassis
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Pro Sweep 5200 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)