CHUTE DIRECTIONAL CONTROL
The spark plug wire was disconnected for safety.
Attach spark plug wire to spark plug before starting.
The chute directional control is located on left hand
side of the snow thrower. See Figure 14.
To change the direction in which snow is thrown, turn
chute directional control as follows:
GAS AND OIL FILL-UP
Check oil level and add oil if necessary. Service the
engine with gasoline as instructed in the separate
engine manual packed with your snow thrower. Read
instructions carefully.
1.
2.
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right.
THROTTLE CONTROL
WARNING: Never fill fuel tank indoors.
Never fill fuel tank with engine running or
while engine is hot. Do not smoke when
filling fuel tank.
The throttle control is located on the engine. It regu-
lates the speed of the engine. See Figure 16.
SAFETY IGNITION SWITCH
TO START ENGINE
The ignition key must be inserted in the switch before
the unit will start. Remove the ignition key when snow
thrower is not in use.
1.
Attach spark plug wire to spark plug. Make cer-
tain the metal loop on end of the spark plug wire
(inside the boot) is fastened securely over the
metal tip on the spark plug. See Figure 17.
FUEL SHUT-OFF
VALVE
Closed
Metal Loop
on Spark
Plug Wire
The fuel shut-off valve,
located under fuel tank,
controls fuel flow from
Open
Rubber Boot
Figure 17
tank. (If equipped)
Figure 15.
See
Figure 15
2.
3.
4.
Make certain the fuel cutoff valve is in the OPEN
(vertical) position.
Make certain the auger and traction controls are
in the disengaged (released) position.
Choke
Primer
Move throttle control up to FAST position. Insert
ignition key into slot. Be certain it snaps into
place. Do not turn key. See Figure 18.
Note: Engine will not start unless ignition key is
inserted into ignition slot in carburetor cover. Do
not turn ignition key.
Recoil Starter:
Rope Starter
Handle
5.
6.
7.
8.
Rotate choke knob to FULL choke position (cold
engine start).
Ignition
Key
Throttle
Control
If engine is warm, place choke in OFF position
instead of FULL.
Figure 16
Push primer button three or four times for cold
engine start.
BEFORE STARTING
If engine is warm, push primer button once only.
WARNING: Observe all Warning Labels
on the snow thrower prior to use. See
Figure 2
NOTE: Always cover vent hole in primer button
when pushing. Additional priming may be necessary
for first start if temperature is below 15 degrees Fahr-
enheit.
Your snow thrower is shipped with oil; however,
you must check the oil level before operating. Be
careful not to overfill.
9.
Grasp starter handle and pull rope out slowly,
until it pulls slightly harder. Let rope rewind
slowly.
11
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals |
|---|---|
| Tags | MTD E600E, MTD E610E, MTD E640F, MTD E660G, MTD E6C0F, MTD Snow Blower Manual, Yard Machines E600E, Yard Machines E610E, Yard Machines E640F, Yard Machines E660G, Yard Machines E6C0F |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yard Machines, E600E, E610E, E640F, E660G, E6C0F, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)