Removing the Carburetor
Heater Box
Important
for the choke and throttle positions.
Use the carburetor heater box as a reference
If you operate the engine when the air temperature is above
Installing the Carburetor
Heater Box
40
_F (4_C), remove the carburetor heater box (Fig. 18).
2
To install the carburetor heater box, reverse steps 1 through
9 of Removing the Carburetor Heater Box on page 15.
Remove the fasteners from their holes before installing the
carburetor heater box.
3
4
Starting the Engine
5
1
Important
Ensure that there are no obstructions in the
6
m-2673
auger/impeller and the discharge chute before you operate
the snowthrower. Use a stick, not your hand, to remove an
obstruction from the auger/impeller or the discharge chute.
Figure 18
1.
2.
3.
Screw and lock washer
Spark-plug wire
Bolt
4.
5.
6.
Carburetor heater box
Bolts
1. Connect the wire to the spark plug.
Screws
2.
3.
Move the throttle to the Fast position.
Release the auger/impeller drive control lever and the
traction control lever (Fig. 15).
1.
Disconnect the wire from the spark plug and ensure that
the wire does not contact the plug (Fig. 18).
4.
Open the fuel shutoff valve below the fuel tank
(Fig. 20).
2.
3.
4.
Remove the key from the ignition switch (Fig. 16).
Pull the choke knob off (Fig. 16).
Remove the fasteners that secure the carburetor heater
box (Fig. 18).
Note: Install these fasteners in their holes for safe
keeping.
2
5.
6.
Lift the carburetor heater box up and away from the
engine.
3
1
726
Disconnect the green ground wire clip under the throttle
(Fig. 19).
Figure 20
1.
2.
Fuel line
3.
Fuel shutoff valve
Hose clamp
5.
6.
Rotate the choke (Fig. 16) to the On position.
Insert the ignition key (Fig. 16).
Important
engine has been running and is hot. Excessive priming may
flood the engine and prevent it from starting.
Do not use the primer or the choke if the
1
mĆ4947
Figure 19
7. Cover the hole in the center of the primer (Fig. 16) with
your thumb and push in the primer 3 times, pausing a
moment between pushes.
1.
Green ground wire clip
8.
Grasp the recoil starter handle (Fig. 17) and pull it out
slowly until positive engagement results; then pull the
handle vigorously to start the engine.
7.
8.
9.
Install the choke knob.
Insert the ignition key.
Connect the wire to the spark plug.
9. Keep a firm grip on the starter handle and return the
rope slowly.
15
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38053, Toro 521, Toro 824 Power Throw |
| Model Number | 38053 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 220000001 - 220999999 |
| Product Name | 824 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Intermediate Frame |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HMSK80-155645W |
| Engine Motor Size | 8 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 5 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)