ASSEMBLY
Assembling the spray guard and
trimmer head Superauto II
Assembling the spray guard and
trimmer head Trimmy SII (235R)
(225R/RD/
232R/RD)
•
Fit the guard (A) intended
for use with the trimmer
head. Secure using four
bolts (L) and the support
plate (M) as shown in the
diagram.
•
Fit the guard (A) intended
for use with the trimmer
head. Secure using the 4
bolts (L) and the support
plate (M) as set out in the
diagram.
A
L
B
• Fit the driver plate (B) on
the drive shaft.
K
•
•
Fit the drive disc (B) on the
output axle.
J
• Rotate the drive shaft so
that one of the holes in the
driver plate lines up with
the corresponding hole in
the gear housing.
I
Turn the blade axle until
one of the holes in the
drive disc aligns with the
hole in the gear housing.
C
M
K
• Insert the locking pin (C)
into the hole to lock the
shaft.
•
•
Insert the locking pin (C)
in the hole so that the axle
is locked.
H
G
•
Screw on the trimmer
head (H) in the opposite
direction to the normal
direction of rotation.
F
B
C
I
The trimmer head must be
split to be fitted (see the
diagram). Proceed as
follows:
M
L
•
•
Tighten the trimmer head
to a torque of 35-50 Nm
(3.5-5
kpm).
•
Insert your finger into the
centre hole of the cover (I)
at the same time as you
hold the cover with your
other fingers. Press the two
catches (J) that extend from
the cut-out on the bottom
section (K) using the
To remove the trimmer
head just reverse the
sequence.
A
Assembling other guards and
cutting equipment
thumb and index finger of
your other hand. Press
apart the trimmer head
using the fingers on the
cover.
• Fit the guard (A)
intended for use with
the trimmer head.
Secure using four bolts
(L) and the support plate
A
L
B
(M) as shown in the
diagram.
•
•
Place the cover (I) and the
support flange (F) on the
output axle.
•
Fit the disc drive (B) on
the output axle.
C
M
Fit the nut (G). The
• Turn the blade axle until
one of the disc drive’s
holes aligns with the
corresponding hole in
the gear housing.
tightening torque of the
nut is 35-50 Nm (3,5-5
kpm). Use the socket
spanner in the tool kit.
Hold the handle of the
spanner as close to the trimmer guard as possible. The nut is
tightened when the spanner is turned against the direction of
rotation (left-hand thread).
H
•
•
•
Insert the locking pin
(C) into the hole to lock
the axle.
Screw on the trimmer
head (H) in the
direction of rotation.
•
•
Fit the trimmer head‘s bottom section (K) on the cover (I)
by pressing the two sections together with the cut-outs on
the bottom section aligned with the catches on the cover.
Dismantling takes place
in the reverse order.
To dismantle follow the instructions in the reverse order.
English –
19
Categories | Chainsaw Manuals, Husqvarna Chainsaw Manuals |
---|---|
Tags | Husqvarna 225R, Husqvarna 225RD, Husqvarna 225RJ, Husqvarna 232R, Husqvarna 232RD, Husqvarna 235R |
Model Year | 1995, 1996, 1997, 1998 |
Download File |
|
Document Type | Operator's Manual |
Language | English |
Product Brand | Husqvarna, Chainsaw |
Document File Type | |
Publisher | husqvarna.com |
Wikipedia's Page | Husqvarna |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)