2
3
1
1
726
mĆ4947
Figure 19
Figure 18
1.
2.
Fuel line
3.
Fuel shutoff valve
1.
Green ground wire clip
Hose clamp
7.
8.
9.
Install the choke knob.
5.
6.
Rotate the choke (Fig. 15) to the On position.
Insert the ignition key.
Insert the ignition key (Fig. 15).
Connect the wire to the spark plug.
Important
Do not use the primer or the choke if the
Important
for the choke and throttle positions.
Use the carburetor heater box as a reference
engine has been running and is hot. Excessive priming may
flood the engine and prevent it from starting.
7.
8.
9.
Cover the hole in the center of the primer (Fig. 15) with
your thumb and push in the primer 3 times, pausing a
moment between pushes.
Installing the Carburetor
Heater Box
Grasp the recoil starter handle (Fig. 16) and pull it out
slowly until positive engagement results; then pull the
handle vigorously to start the engine.
To install the carburetor heater box, reverse steps 1 through
9
of Removing the Carburetor Heater Box on page 14.
Remove the fasteners from their holes before installing the
carburetor heater box.
Keep a firm grip on the starter handle and return the
rope slowly.
Note:–10_FIf(–23the_engineC) or colder,does notthestartengineor ifmaythe needair temperatureadditional is
Starting the Engine
priming. After pushing in the primer, try to start the engine
before priming again.
Important
Ensure that there are no obstructions in the
auger/impeller and the discharge chute before you operate
the snowthrower. Use a stick, not your hand, to remove
an obstruction from the auger/impeller or the discharge
chute.
10. After the engine starts, immediately rotate the choke
(Fig. 15) to the 3/4 position. As the engine warms up,
rotate the choke to the 1/2 position. When the engine
warms up sufficiently, rotate the choke to the Off
position.
1.
2.
3.
Connect the wire to the spark plug.
Move the throttle to the Fast position.
11.
Move the speed selector (Fig. 14) to first gear, squeeze
the traction control lever to the handgrip, and then
release the traction control lever. If the snowthrower
moves forward before engaging the traction drive
control lever or after releasing the lever, see Adjusting
the Traction Drive Belt on page 20.
Release the auger/impeller drive control lever and the
traction control lever (Fig. 14).
4.
Open the fuel shutoff valve below the fuel tank
(Fig. 19).
Important
Do not operate the snowthrower if the auger
and impeller rotate when you disengage the auger/impeller
drive control lever.
15
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38053, Toro 521, Toro 824 Power Throw |
| Model Number | 38053 |
| Model Year | 2003 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 230000001 - 230999999 |
| Product Name | 824 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Intermediate Frame |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HMSK80-155645W |
| Engine Motor Size | 8 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 5 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 38053 824 Power Throw Snowblower Operators Manual, 2003 5.0 out of 5.0 based on 1 product reviews. the Toro 824 is a great little piece of machinery