6.
Support the auger blades so that they are 1/8 inch
2. Disconnect the wire from the spark plug and ensure that
(3
millimeters) off the ground (Fig. 22).
the wire does not contact the plug (Fig. 17).
3.
Move the speed selector (Fig. 14) on the control panel
to the R2 (Reverse) position.
3
4.
5.
Remove the cotter pin and the flat washer (Fig. 5).
Pull the speed selector rod out of the hole in the speed
selector arm (Fig. 5).
2
2
6.
Adjust the forward speed by rotating the speed selector
rod in the trunnion (Fig. 6).
Note: Lengthening the rod makes the forward speed
faster; shortening the rod makes the forward speed
slower.
1
652
7.
8.
Insert the speed selector rod into the speed selector arm
and secure it with the flat washer and cotter pin.
Figure 22
1.
2.
Scraper
3. Auger blades
Connect the wire to the spark plug.
Mounting screws
Adjusting the Traction Drive
Belt
7.
Check the scraper adjustment. The scraper should be
inch (3 millimeters) above and parallel to a level
surface.
1/8
Check the traction drive belt for the proper tension after the
first operating hour, after every 5 operating hours
thereafter, and when the speed selector shifts properly but
the snowthrower does not drive in the forward or reverse
speeds. Adjust the belt when necessary.
For Concrete and Asphalt Surfaces:
If the snowthrower does not clear the snow close enough to
the pavement, adjust the skids to lower the scraper; if the
pavement surfaces are cracked, rough, or uneven, adjust the
skids to raise the scraper.
1.
2.
Stop the engine and wait for all moving parts to stop.
For Gravel Surfaces:
Disconnect the wire from the spark plug and ensure that
the wire does not contact the plug (Fig. 17).
Support the auger blades a few inches (centimeters) above
the ground, and adjust the skids to prevent the snowthrower
from picking up rocks.
3.
Check the adjustment according to steps 3 through 6 of
Installing the Traction Rod on page 10. Make any
needed adjustments.
8.
To adjust the scraper, loosen the 5 mounting screws
(Fig. 22), level the scraper, and tighten the mounting
screws.
4.
5.
If the linkage is properly adjusted and the problem
persists, contact an Authorized Service Dealer.
9.
Move the skids down as far as possible.
Connect the wire to the spark plug.
10.
Tighten the 4 flange nuts that secure both skids to the
auger side plates (Fig. 21).
Replacing the Traction Drive
Belt
11.
Connect the wire to the spark plug.
If the traction drive belt becomes worn, oil-soaked, or
otherwise damaged, replace the belt.
Adjusting the Speed Selector
Adjust the speed selector linkage initially and when the
snowthrower is slow, first gear has no speed, or the speed
selector does not move into fifth gear.
1. Stop the engine and wait for all moving parts to stop.
2.
Disconnect the wire from the spark plug and ensure that
the wire does not contact the plug (Fig. 17).
1.
Stop the engine and wait for all moving parts to stop.
20
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38053, Toro 521, Toro 824 Power Throw |
| Model Number | 38053 |
| Model Year | 2003 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 230000001 - 230999999 |
| Product Name | 824 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Intermediate Frame |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HMSK80-155645W |
| Engine Motor Size | 8 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 5 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 38053 824 Power Throw Snowblower Operators Manual, 2003 5.0 out of 5.0 based on 1 product reviews. the Toro 824 is a great little piece of machinery