5.
Installing the Chute Control
Rod
Chute control rod assembly (rod and bracket, worm
gear, and bracket)
1
1
1
1
2
Carriage bolt
Belleville washer
Hex head bolt
Locknut
Procedure
1.
Assemble the chute control bracket and rod to the
left side of the handle with the bolt and the locknut
as shown in Figure 10.
Figure 9
1.
2.
Handgrip
3.
4.
1 to 2 inches (3 to 5 cm)
5 inches (12.7 cm)
Auger/impeller control
lever
Note: The distance should be approximately 5
inches (12.7 cm).
4.
Press the auger/impeller drive control lever slowly
toward the handgrip.
Figure 10
1.
Chute control bracket and
rod
2. Hex head bolt and locknut
Note: The amount of force needed to compress the
lever increases noticeably when you remove the slack
from the auger/impeller drive belt (approximately
Note: Do not tighten the locknut.
1/2
of the lever movement). The adjustment is
correct when the force begins to increase and the
distance between the top of the handgrip and the
bottom of the auger/impeller drive control lever is 1
to 2 inches (3 to 5 cm) as shown in Figure 9.
2.
Apply No. 2 general purpose grease to the worm
gear (Figure 11).
Note: If the force does not noticeably increase,
remove the belt cover (refer to step 2 of Replacing
the Traction Drive Belt in Maintenance) and measure
2
inches (5 cm) above the handgrip at the point
where you remove the slack from the auger/impeller
drive belt.
5.
To adjust the distance:
A. Remove the clevis pin.
B. Loosen the jam nut.
C. Thread the clevis up or down to increase or
decrease the distance between the top of the
handgrip and the bottom of the auger/impeller
drive control lever (Figure 8).
Figure 11
1.
Worm gear
Bracket
3.
4.
Mounting flange
2.
Carriage bolt, Belleville
washer, and locknut
6.
7.
When the adjustment is correct, install the clevis pin
and secure it in place with the cotter pin (Figure 8).
Tighten the jam nut to secure the clevis (Figure 8).
10
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38605, Toro Power Max 522 |
| Model Number | 38605 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 270000001 - 270004504 |
| Product Name | Toro 522 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | Auger 5 oz. Lubriplate Mag 1 grease |
| Engine Motor Model # | LH195SA-67435V |
| Engine Motor Size | 22 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)