Product Overview
•
•
Traction Control Lever—To engage the traction
(wheel drive), press the lever against the left
handgrip. To stop the traction, release the lever.
Speed Selector Lever—This control has 4
positions: 3 forward speeds and 1 reverse. To change
speeds, move the speed selector lever to the desired
position. The lever locks in a notch at each speed
selection.
Note: Before shifting gears into or out of reverse,
you must release the traction control lever. You may
shift between any of the forward speeds without
releasing the traction control lever.
Figure 13
• Discharge Chute Control—Rotate the discharge
chute control clockwise to move the discharge chute
to the left; counterclockwise to move the chute to
the right.
1.
Auger/impeller drive
control lever
4.
Discharge chute control
2.
3.
Traction control lever
Speed selector lever
5.
6.
Chute deflector handle
Fuel shutoff valve
•
Chute Deflector Handle—Move the deflector
handle forward to move the snow stream down;
move it rearward to move the snow stream up.
•
Fuel shutoff Valve—Close the valve by rotating
clockwise. Open the valve by rotating it
counterclockwise. Close the valve when you do not
use the snowthrower.
•
•
•
Ignition Switch—Insert the ignition key before
starting the engine. To stop the engine, remove the
key.
Choke—Move the choke to the Full position to
start a cold engine. As engine warms up, gradually
move the choke to the Off position.
Throttle Lever—Move the throttle lever upward
to increase the engine speed; move it downward to
decrease the engine speed. Move the throttle lever to
the Stop position to stop the engine.
Figure 14
1.
Ignition switch
4.
Primer
2.
3.
Choke
Throttle
5.
6.
Electric starter
Recoil starter
•
•
Primer—Press the primer to pump a small
amount of gasoline into the engine for improved
cold-weather starting.
Electric Starter—The electric starter is on the top
of the engine. To start the snowthrower, connect
the electric starter to an electric power source with
an approved extension cord and press the starter
button.
Figure 15
1.
Snow clean-out tool (attached to the top of the auger
housing)
•
•
Recoil Starter—The recoil starter is on the back
side of the engine. Pull the recoil starter to start the
engine.
Controls
•
Auger/Impeller Drive Control Lever—To engage
both the auger and impeller, press the lever against
the right handgrip. To disengage, release the lever.
Snow Clean-out Tool—The snow clean-out tool
is on the top of the auger housing. Use this tool to
unclog the discharge chute when it becomes clogged
with snow.
12
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38605, Toro Power Max 522 |
| Model Number | 38605 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 270000001 - 270004504 |
| Product Name | Toro 522 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | Auger 5 oz. Lubriplate Mag 1 grease |
| Engine Motor Model # | LH195SA-67435V |
| Engine Motor Size | 22 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)