2.
3.
Move the speed selector lever (Figure 13) on the
control panel to the R (Reverse) position.
top of the handgrip and the bottom of the traction
control lever is 1 to 2 inches (3 to 5 cm) as shown
in Figure 7.
Install the speed selector rod into the speed selector
arm, add a flat washer on the selector rod, and secure
it with a cotter pin (Figure 6).
6.
Adjust the 2 flange nuts, if necessary, to obtain the
proper distance between the top of the handgrip and
the bottom of the traction control lever.
3.
Installing the Traction Rod
7.
Tighten the flange nuts securely.
1
Flange locknut
4.
Installing the Auger/ Impeller
Procedure
Drive Control Linkage
1.
Thread the flange locknut (flange side up) onto the
bottom of the traction control rod, below the loop
in the lower traction rod (Figure 4).
1
1
Clevis pin
Cotter pin
2.
Adjust the 2 flange nuts up or down on the traction
rod until the distance between the top of the
handgrip and the bottom of the traction control
lever is approximately 4-1/2 inches (11.4 cm) as
shown in Figure 7.
Procedure
1.
Loosen the jam nut above the clevis on the upper
control rod (Figure 8).
Figure 7
1.
Handgrip
3.
4.
1 to 2 inches (3 to 5 cm)
4-1/2 inches (11.4 cm)
2.
Traction control lever
Figure 8
1.
Upper control rod
4.
Cotter pin
3.
Tighten the 2 flange nuts until they are finger tight.
2.
3.
Jam nut
Clevis
5.
6.
Lower control rod
Clevis pin
4.
Move the speed selector lever (Figure 13) into third
gear.
2.
Align the holes in the clevis and the lower control
rod and insert the clevis pin (Figure 8).
Note: If the speed selector lever does not move
into third gear, adjust the speed selector before
continuing. Refer to Adjusting the Speed Selector
in Maintenance.
3.
Check the distance between the top of the handgrip
and the bottom of the auger/impeller drive control
lever (Figure 9).
5.
Slowly pull the snowthrower backward while slowly
pressing the traction control lever toward the
handgrip.
Note: The adjustment is correct when the wheels
stop rolling backward and the distance between the
9
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38605, Toro Power Max 522 |
| Model Number | 38605 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 270000001 - 270004504 |
| Product Name | Toro 522 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | Auger 5 oz. Lubriplate Mag 1 grease |
| Engine Motor Model # | LH195SA-67435V |
| Engine Motor Size | 22 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)