3.
Loosely mount the worm gear and the bracket to the
mounting flange with a bolt, a Belleville washer, and
a locknut as shown in Figure 11.
5. Wipe the dipstick clean with a clean cloth.
6.
Install the dipstick into the filler neck, then remove it.
Note: To ensure an accurate oil level reading, you
must fully install the dipstick.
4.
5.
6.
Slide the worm gear into the teeth of the chute
retaining ring and tighten the locknut (Figure 11).
7.
8.
Read the oil level on the dipstick.
Tighten the locknut that secures the chute control
bracket (Figure 10).
If the oil level is below the Add mark on the dipstick,
slowly pour only enough oil into the filler hole to
raise the oil level to the Full mark on the dipstick.
Check the operation of the chute control rod, and
move the worm gear slightly outward if it binds.
Important: Do not overfill the crankcase with
oil and run the engine; engine damage will
result. Drain the excess oil until the oil level on
the dipstick reads Full.
6.
Filling the Engine with Oil
Procedure
9.
Insert the dipstick into the filler neck and rotate the
cap clockwise until it is tight.
Your snowthrower comes with 21 oz. (0.62 l) of oil in
the engine.
Note: Before starting the engine, check the oil level
and add oil if necessary.
7.
Checking the Tire Pressure
Max. fill: 21 oz. (0.62 l), type: automotive detergent
oil with an API service classification of SF, SG, SH, SJ,
SL, or higher.
Procedure
The tires are overinflated at the factory for shipping.
Reduce the pressure equally in both tires to between 12
and 15 psi (82 and 103 kPa).
•
•
For temperatures above 32°F (0°C), use SAE 30.
For temperatures between 0°F and 32°F (-18°C to
0°C),
use SAE 5W30 or SAE 10.
8.
Scraper
Checking the Skids and
•
For air temperatures below 0°F (-18°C), use
SAE 0W30.
1.
2.
Move the snowthrower to a level surface to ensure
an accurate oil level reading.
Procedure
Clean around the dipstick (Figure 12).
Refer to Checking and Adjusting the Skids and Scraper
in Maintenance.
Figure 12
1.
Fuel tank cap
Dipstick
3. Filler hole
2.
3.
Remove the dipstick by rotating the cap
counterclockwise and pulling it out.
4.
Slowly pour about 3/4 of the crankcase capacity of
oil into the crankcase.
11
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38605, Toro Power Max 522 |
| Model Number | 38605 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 270000001 - 270004504 |
| Product Name | Toro 522 Power Throw Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | Auger 5 oz. Lubriplate Mag 1 grease |
| Engine Motor Model # | LH195SA-67435V |
| Engine Motor Size | 22 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)